Snap-On ControlTech Micro Скачать руководство пользователя | Manualshive

Страница: 2 / 36

background image

1

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Risk of flying particles.

Over-torquing can cause breakage. Force against flex stops on flex head can cause
head breakage. An out of calibration angle wrench can cause part or tool
breakage. Broken hand tools, sockets or accessories can cause injury. Excess force
can cause crowfoot or flare nut wrench slippage.

Read

this manual completely

before using ELECTRONIC WRENCH.

To ensure accuracy, work must not move in angle mode.

For personal safety and to avoid wrench damage, follow good professional tool
and fastener installation practices.

Periodic recalibration is necessary to maintain accuracy.

Wear safety goggles, user and bystanders.

Be sure all components, including all adaptors, extensions, drivers and sockets
are rated to match or exceed torque being applied.

Observe all equipment, system and manufacturer's warnings, cautions and
procedures when using this wrench.

Use correct size socket for fastener.

Do not use sockets showing wear or cracks.

Replace fasteners with rounded corners.

To avoid damaging wrench:

Never use wrench with power off. Always turn ON

wrench so applied torque is being measured.

Do not press

POWER

while torque is applied or while wrench is in motion.

Never use this wrench to break fasteners loose.

Do not use extensions, such as a pipe, on handle of wrench.

Check that wrench capacity matches or exceeds each application before
proceeding.

When using negative offsets, verify maximum targets are not exceeded (see
tables on page 6).

Verify calibration if dropped.

Make sure ratchet direction lever is fully engaged in correct position.

Verify calibration of wrench if you know or suspect its capacity has been
exceeded.

Do not force head of flex head drives against stops.

Always adjust your stance to prevent a possible fall should something give
while using wrench.

Do not attempt to recharge lithium cells.

Store wrench in dry place.

Remove batteries when storing wrench used for periods longer than 3 months.

WARNING

Electrical Shock Hazard.

Electrical shock can cause injury. Metal handle is not isolated.
Do not use on live electrical circuits.

SAVE THESE INSTRUCTIONS

Disclaimer

Operation of ControlTech

TM

Micro Wrench is not warranted in an EU member state if

operating instructions are not in that State’s language. Contact Snap-on if a translation
is needed.

«
1
2
3
4
...
»

Содержание ControlTech Micro





































Отзывы:

Нет отзывов

Похожие инструкции для ControlTech Micro

Бренд: GE Страницы: 50

Бренд: FEDERAL PACIFIC Страницы: 4

Бренд: KEB Страницы: 46

Performance IntelliSUPPLY PSC15

Бренд: XS Power Batteries Страницы: 24

Бренд: Eaton Страницы: 10

Alligator Staple Gold Class

Бренд: Flexco Страницы: 2

Бренд: THERMOBILE Страницы: 66

Element S Split M5

Бренд: Scell-it Страницы: 42

Бренд: Promaker Страницы: 24

Бренд: Galaxy Страницы: 11

Бренд: Et system Страницы: 83

Бренд: Baileigh Industrial Страницы: 24

Бренд: Pulsar Страницы: 4

Бренд: N.KO Страницы: 22

Бренд: easydriver Страницы: 13

Бренд: HuntKey Страницы: 4

Бренд: tekton Страницы: 8

Бренд: coocazoo Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды