SMT SMT-1100W Скачать руководство пользователя страница 4

4

Warnings

These "WARNING" labels are affixed to your system for all operators to read. 

If they have been removed or are unreadable, please call 

(800)548-3373

 or  

(479) 636-5776

 to order replacements.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

 - When using this product, basic precautions should always be followed, including the following:

• 

Read all the instructions before using the product.

• 

To reduce the risk of injury, close supervision is necessary when a product is used near children.

• 

Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls.

• 

Stay alert - watch what you are doing.

• 

Do not operate the product when fatigued or under the influence of alcohol or drugs.

• 

Keep operating area clear of all persons.

• 

Do not overreach or stand on unstable support. Keep good footing and balance at all times.

• 

Follow the maintenance instructions specified in the manual.

• 

NEVER

 

look directly into a nozzle. Always release the pressure in the high pressure hose by opening the spray gun after machine is 

shut off.

• 

For a grounded product rated 250 Volts, single phase or less:

"This product is provided with a Ground Fault Circuit Interrupter built into the power cord plug. If replacement of the 

plug or cord is needed, use only identical replacement parts." 
Replace complete GFCI cord assembly if either the GFCI, plug or cord is damaged, frayed or worn.

WARNING - Risk of injection or injury - Do not directly discharge stream at persons.

SAVE THESE INSTRUCTIONS

Risk of Fire, Electric Shock or Personal Injury

Note:  Labels on this page are not to scale.

Содержание SMT-1100W













Отзывы: