Smiths Medical 6101 Скачать руководство пользователя страница 9

Страница: 9 / 29

Battery Compatibility

Recommended Batteries

Nine‑volt alkaline or lithium batteries are

recommended for use in the CADD‑Prizm

PCS II pump. Carbon‑zinc, mercury, nickel‑

cadmium, or zinc‑air 9‑volt batteries should

not be used.

Battery Life

The CADD‑Prizm

PCS II pump has been

designed to provide optimal battery life. The

expected battery life in the CADD‑Prizm

PCS

II pump depends on the following factors:
•  Programmed delivery rate
•  Operating temperatures
•  Frequency of display backlighting
•  Frequency of printing
•  Battery type and brand
•  Battery age

DURACELL

Alkaline Battery Life

The following tables may be used to predict

typical alkaline battery life at different delivery

rates when an alkaline battery is used in the

CADD‑Prizm

PCS II pump. As expected,

battery life decreases as the delivery rate

increases. These tables are based on

laboratory tests using fresh DURACELL

alkaline batteries in CADD‑Prizm

PCS II

pumps while the pumps were operating at

room temperature.
Actual battery life may be significantly shorter

depending on the operating temperature and

the storage conditions of the battery.
Battery life is shortened significantly at very

low operating temperatures. For example,

at 0°C (32°F), an alkaline battery will yield

approximately 30% of its normal capacity.
Alkaline batteries do not need to be stored in a

refrigerator. After four years of storage at 21°C

(70°F), an alkaline battery retains approximately

86% of its original capacity. Battery life will

be shorter if the battery is stored above room

temperature. An alkaline battery stored at 43°C

(110°F) will be down to approximately 80% of its

capacity within one year.

3 Batteries

Recommended storage conditions are 10°C

to 25°C (50°F to 77°F) with no more than 65%

relative humidity noncondensing.
The following tables are based on laboratory

tests conducted at room temperature using fresh

DURACELL

alkaline batteries and a CADD

administration set. Actual battery life will vary

depending on the brand of battery, battery shelf

life and temperature conditions.

ULTRALIFE

Lithium Battery Life

The following tables may be used to predict

typical lithium battery life at different delivery

rates when a lithium battery is used in the

CADD‑Prizm

PCS II pump. As expected, battery

life decreases as the delivery rate increases.

These tables are based on laboratory tests

using fresh ULTRALIFE

lithium batteries in

CADD‑Prizm

PCS II pumps while the pumps

were operating at room temperature.
Actual battery life may be significantly shorter

depending on the operating temperature

and the storage conditions of the battery.

Lithium battery life is dependent upon the

temperature and relative humidity of storage.

Recommended storage conditions are less

than 20°C (68°F) with a desiccant to ensure

less than 10% relative humidity.
The following tables are based on laboratory

tests conducted at room temperature using

fresh ULTRALIFE

lithium batteries and a

CADD

administration set. Actual battery life

depends upon the brand of battery selected, the

particular battery selected, battery shelf life, and

temperature conditions. Smiths Medical’s testing

indicates a large variability in battery life.

Содержание 6101






























Результаты поиска

Содержание 6101

Отзывы:

Похожие инструкции для 6101

Бренды по названию

Популярные бренды

Smiths Medical 6101, Техническое руководство

Результаты поиска

Содержание 6101

Отзывы:

Похожие инструкции для 6101

Бренды по названию

Популярные бренды