Smiths Medical 6101 Скачать руководство пользователя страница 24

Страница: 24 / 29

Remote Dose Cord Check

• Check the Remote Dose Cord button

operation by programming the pump with

the following values:
Units

Milligrams

Concentration

1.0 mg/ml

Continuous Rate

0.0 mg/hr

Demand Dose

1.0 mg

Demand Dose Lockout 0 hrs 5 min

Delivery Limit

No Limit

Reservoir Volume

10.0 ml

Dose Counters

0/0 (Press the

ENTER key to clear

in the Reports

menu)

Milligrams Given

0.00 mg (Press the

ENTER key to clear

in the Reports

menu)

• Press the STOP/START key. Press the YES

key. The pump should sequentially display

all of the programmed values.

• After RUNNING appears on the display,

press the Remote Dose Cord button and

note the time. The pump should beep twice

and begin to deliver. Count the number of

pump activations. The pump should make

ten double activations. After ten double

activations, the display should show a

reservoir volume of 9.0 ml. Press the Remote

Dose Cord button two more times within the

next 5 minutes. The pump should not deliver

and the message “Dose Not Delivered Dose

Locked Out” should be displayed.

Doses Given and Doses Attempted Check

• Stop the pump by pressing the STOP/START

key, then the YES key. Press the REPORTS

key to advance to the Dose Counters report.

The display should show 1/3. (If the above

steps have not been followed exactly,

different values may appear.)

• Press the ENTER key. The display should

now show 0/0.

MG GIVEN Report Check

• Press the REPORTS key to advance to the

Milligrams Given report. The display should

now show 1.0 mg if the Remote Dose cord

was tested. (If the above steps have not been

followed exactly, different values may appear.)

• Press the ENTER key. The display should

now show 0.0 mg.

Air Detector Test (if applicable)

This test will verify the function of the optional

air detector. To perform this test, the

CADD‑Prizm

PCS II pump must have an air

detector installed and the air detector must

be turned on. The previous program from

the DOSE key check can be used to perform

this test.

• Attach an empty CADD

™

medication

cassette reservoir or CADD

administration

set to the pump.

• Latch and lock the set to the pump.
• Open the air detector door and thread the

tubing through the groove.

• Close the door making sure the tubing does

not get pinched or kinked.

• Start the pump.
• The pump should respond with a continuous

two‑tone alarm and the display should read

Air in line detected, Pump will not run VIEW

to silence,

• Press VIEW/SILENCE to silence the alarm,

and remove the CADD

™

medication cassette

reservoir or CADD

administration set.

• Now attach a CADD

™

medication cassette

reservoir containing fluid and a primed

extension set with anti‑siphon valve, or

a primed CADD

administration set with

anti‑siphon valve to the pump. Make certain

there is no air in the fluid path.

• Latch and lock the set to the pump.
• Open the air detector door and thread the

tubing through the groove.

• Close the door making sure the tubing does

not get punched or kinked.

• Start the pump.
• Deliver a demand dose. (NOTE five minutes

must have passed since the delivery of the

last demand dose.)

• The pump should deliver the dose without

an air detection alarm.

Occlusion Accuracy Tests

This manual provides two testing options for

the Occlusion Pressure Range Test and the

Accuracy Test. Only one option needs to be

performed. It is not necessary to perform

both Option 1 and Option 2.

Содержание 6101






























Результаты поиска

Содержание 6101

Отзывы:

Похожие инструкции для 6101

Бренды по названию

Популярные бренды

Smiths Medical 6101, Техническое руководство

Результаты поиска

Содержание 6101

Отзывы:

Похожие инструкции для 6101

Бренды по названию

Популярные бренды