Smiths Medical 6101 Скачать руководство пользователя страница 8

Страница: 8 / 29

Date Format

US Standard (mm/dd/yy) or European

Standard (dd/mm/yy). Default: U.S. Standard

Custom Main Display

Display:
• Res Vol or Continuous Rate
• Power Source Always or Low 9 volt battery only

Default: Res Vol and Low 9V

Auto Review*

Select the automatic program review feature

during the pump’s power‑up sequence.

Default: On

• Dose Counters (0 to 999 Given and/or

Attempted). Default: On

• Given. Default: On

• Doses Hour By Hour (up to 48 hours in

increments of 1 hour). Default: Off

• Patient Review. Default: Off

• Pain Scale (subjective pain scale rating of

0 to 10 in increments of 1). Default: On

• Pain Scale Log (0 to 500 entries). Default: On

• Delivery Log (0 to 500 events). Default: Off

• Event Log (0 to 500 events). Default: Off

• New Patient Marker. Default: On

New Patient Marker*

Reports/No Clear, Power‑up/No Clear,

Reports/Clear, Power‑up/Clear
Default: Reports/No Clear

Air Detector Required

Required or Not Required.

Default: Not Required

Default:ing the Lock Level Code &

Clinician Bolus Code

The standard Lock Level Code (061) can be

changed to a customized code using the

Biomed Toolbox Custom Lock Code feature.

See the

Operator’s Manual

supplied with the

pump for instructions on customizing the Lock

Level Code. If it becomes necessary to change

a customized code back to the standard Lock

Level Code, do the following:

1. Press the OPTIONS key until the Lock Level

screen appears

2. Press the ENTER key twice

3. Scroll to 911

4. Press the OPTIONS key

Compatible Reservoirs and

Administration Sets

• 50‑ml or 100‑ml CADD

™

medication

cassette reservoir, used with the CADD

extension set with anti‑siphon valve.

• CADD

administration set with integral

anti‑siphon valve, with or without bag spike

(allows use of flexible plastic bag or sterile

vial with injector)

• CADD

administration set with add on

anti‑siphon valve and bag spike (allows for

gravity priming before attaching the add on

anti‑siphon valve)

Remote Dose Cord

Smiths Medical provides a Remote Dose Cord

for the PCA delivery mode. The push button

switch is a Single Pole Double Throw (SPDT).

When the Remote Dose Cord is attached to the

pump, the patient may press the Remote Dose

button to receive a Demand Dose. The clinician

may use the Remote Dose button to deliver a

clinician bolus. For easy access, the Remote

Dose cord may be fastened to the patient’s

clothing or bedsheet with the attached clip.

NOTE

To detach the Remote Dose cord from the

pump, grasp the Remote Dose cord connector

and pull back using a straight, steady motion.

Do not twist or turn the connector, or use

any instrument to remove it. For additional

specifications refer to the

Operator’s Manual

provided with the product.

Note The CADD‑Sentry

Medication Software programming mode must be used to change a customized code back to the standard lock level

code with CADD‑Prizm

PCS II pumps with software revision E or higher.

* If programmed to be part of pump programming screens in Biomed Toolbox.

Содержание 6101






























Результаты поиска

Содержание 6101

Отзывы:

Похожие инструкции для 6101

Бренды по названию

Популярные бренды

Smiths Medical 6101, Техническое руководство

Результаты поиска

Содержание 6101

Отзывы:

Похожие инструкции для 6101

Бренды по названию

Популярные бренды