Smithco 100684 Скачать руководство пользователя страница 84

Страница: 84 / 94

Accessories

30-006 FRESH WATER WASH TANK DRAWING

REF# PART#

DESCRIPTION

QUANTITY

10-234

Wash Tank

16-158

Close Nipple

16-151

Elbow

16-960

Spigot

HB-516-18-075

Bolt

- 18 x

HWL-516

Lockwasher

HW-516

Washer

1. Fresh Water Wash Tank mounts on the rear of all the machines.
2. The Bracket is already attached to the Super Boom center boom post.
3. Install the nipple (Ref 2), elbow (Ref 3) and spigot (Ref 4) into the bottom of wash tank (Ref 1). Use

thread tape on all threads.

4. Mount the tank onto the mount bracket using four

bolts, washers and lockwashers. Tighten.

5. Rinse tank with clear water and check for leaks around fittings.

This tank is for fresh clear water ONLY. Do not put chemicals in this tank.

Содержание 100684































































































Результаты поиска

Содержание 100684

Отзывы:

Похожие инструкции для 100684

Бренды по названию

Популярные бренды

Smithco 100684, Запчасти и обслуживание

Результаты поиска

Содержание 100684

Отзывы:

Похожие инструкции для 100684

Бренды по названию

Популярные бренды