manualshive.com logo in svg

Smith & Nephew Syncera Anthem, Хирургические техники

Поделиться
Скачать
Smith & Nephew Syncera Anthem Скачать руководство пользователя страница 28

26

4.

 Flex the knee to 90° keeping the thin bent Hohmann 

laterally and removing the Aufranc retractor. Mix and 
prepare bone cement for femoral component and 
distal femur. Apply cement to the femoral component 
or prepared bone, based on the surgeon’s preference 
(Figure 26b). 

Note: Care should be taken to avoid excess cement 
on the posterior aspect of the femur and femoral 
component. Excess cement that extrudes posteriorly is 
difficult to remove.

5.

 Place the Femoral Implant onto the femur and use the 

Modular Femoral Impactor to fully seat the implant. 
Remove excess cement. Extend the knee to remove 
cement anteriorly without retracting the proximal soft 
tissue (Figure 26c).

Note: Similar to the femoral trial impactor, the femoral 
implant impactor can be used to impact into the 
femoral notch as well as on to the distal surface of the 
component by rotating through 180 degrees. This can 
be used to prevent the component tilting into flexion 
during impaction.

Figure 26b

Figure 26c

Содержание Syncera Anthem

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды