SNMP Commands
24-14
24
snmp-server user
This command adds a user to an SNMP group, restricting the user to a specific
SNMP Read, Write, or Notify View. Use the
no
form to remove a user from an SNMP
group.
Syntax
snmp-server user
username
groupname
[
remote
ip-address
] {
v1
|
v2c
|
v3
[
encrypted
] [
auth
{
md5
|
sha
}
auth-password
[
priv des56
priv-password
]]
no snmp-server user
username
{
v1
|
v2c
|
v3
|
remote
}
•
username
- Name of user connecting to the SNMP agent.
(Range: 1-32 characters)
• groupname -
Name of an SNMP group to which the user is assigned.
(Range: 1-32 characters)
•
remote
- Specifies an SNMP engine on a remote device.
•
ip-address
- The Internet address of the remote device.
•
v1
|
v2c
|
v3
- Use SNMP version 1, 2c or 3.
•
encrypted
- Accepts the password as encrypted input.
•
auth
- Uses SNMPv3 with authentication.
•
md5
|
sha
- Uses MD5 or SHA authentication.
•
auth-password
- Authentication password. Enter as plain text if the
encrypted
option is not used. Otherwise, enter an encrypted password.
(A minimum of eight characters is required.)
•
priv des56
- Uses SNMPv3 with privacy with DES56 encryption.
•
priv-password
- Privacy password. Enter as plain text if the
encrypted
option is not used. Otherwise, enter an encrypted password.
Default Setting
None
Command Mode
Global Configuration
Command Usage
• The SNMP engine ID is used to compute the authentication/privacy digests
from the password. You should therefore configure the engine ID with the
snmp-server engine-id
command before using this configuration command.
• Before you configure a remote user, use the
snmp-server engine-id
command (page 24-8) to specify the engine ID for the remote device where
the user resides. Then use the
snmp-server user
command to specify the
user and the IP address for the remote device where the user resides. The
remote agent’s SNMP engine ID is used to compute authentication/privacy
digests from the user’s password. If the remote engine ID is not first configured,
the
snmp-server user
command specifying a remote user will fail.
• SNMP passwords are localized using the engine ID of the authoritative agent.
For informs, the authoritative SNMP agent is the remote agent. You therefore
Содержание 8926EM
