background image

SwitchLinc V2 Relay User’s Guide 

 

Unlinking a Controlled INSTEON Device from SwitchLinc Relay 

If you are no longer going to use an INSTEON Device that has previously been linked to SwitchLinc 
Relay, it is very important that you unlink it, because otherwise SwitchLinc Relay will retry any commands 
intended for the unused INSTEON Device, thus slowing down your system. 

1.  Set SwitchLinc Relay to 

Linking Mode

 by pressing and holding the 

Paddle Top

 for 10 seconds until 

the top LED in the LED Bar begins blinking slowly and the controlled light flashes. 

2.  Set SwitchLinc Relay to 

Unlinking Mode

 by pressing and holding the 

Paddle Top

 

again

 for 10 

seconds until the controlled light flashes again. 

3.  Follow the same method given above that you used to link your INSTEON Device to unlink it.  On 

most INSTEON Devices, you just push an 

ON Button

 for 10 seconds or a 

SET Button

 for 3 seconds. 

4.  Go back to the SwitchLinc Relay that you placed in Unlinking Mode.  If linking was successful, the top 

LED in its LED Bar will not be blinking but will remain steadily on. 

Creating an INSTEON Scene 

INSTEON Scenes let you activate dramatic lighting moods with the press of just one button.  INSTEON 
Scenes are very easy to set up – just link more than one INSTEON Device to SwitchLinc Relay.  Then, 
when you press either the Paddle Top or Paddle Bottom on SwitchLinc Relay, all of the INSTEON 
Devices linked in the scene will respond as a group.  You can link multiple INSTEON Devices to multiple 
of INSTEON Controllers. 

To add an additional INSTEON Device to a scene controlled by SwitchLinc Relay, simply follow the same 
procedure as above in 

Linking SwitchLinc Relay to a Controlled INSTEON Device

.    To  remove  an 

INSTEON Device from a scene, see 

Unlinking a Controlled INSTEON Device from SwitchLinc Relay

TIP 

 
You can avoid having to hold SwitchLinc Relay’s Paddle Top down for 10 seconds for each INSTEON
Device in a scene by placing SwitchLinc Relay in 

Scene Setup Mode

, also called 

Multilink Mode

1.  Set SwitchLinc Relay to Scene Setup Mode by 

pressing and holding the 

Paddle Top

 for 10 

seconds, then pressing the 

SET Button

 at the 

bottom of the paddle.  SwitchLinc Relay’s top 
LED in the LED Bar will blink slowly. 

 

 

2.  Follow the linking method given above for the INSTEON Device you want to include in the scene.

On most INSTEON Devices, you just push an ON Button for 10 seconds or a SET Button for 3
seconds.  SwitchLinc Relay will flash its controlled light to confirm linking, and the top LED in its
LED Bar will continue to blink slowly. 

3.  On some INSTEON Devices, you may be able to set up additional features, such as On-Levels or

Ramp Rates at this time. 

4.  Continue Steps 2 and 3 for any additional INSTEON Devices you want to link to the scene. 

5.  When you are finished linking INSTEON Devices to SwitchLinc Relay, complete Scene Setup by

pressing the 

Paddle Top

 (actually, 

any

button press will terminate Scene Setup).  The top LED in

SwitchLinc Relay’s LED Bar will stop blinking and remain steadily on.  You have about 4 minutes
of inactivity before SwitchLinc Relay’s Scene Setup Mode times out automatically. 

 

Page 15 of 32 

 

Содержание 2476S

































Отзывы: