background image

SwitchLinc V2 Relay User’s Guide 

 

HOW TO SET UP SWITCHLINC RELAY TO REMOTELY CONTROL AN 
INSTEON DEVICE 

Linking SwitchLinc Relay to a Controlled INSTEON Device 

To use SwitchLinc Relay as an INSTEON Controller, follow these steps to link SwitchLinc Relay and a 
controlled INSTEON Device together.  Refer to your INSTEON Device’s User’s Guide for detailed 
instructions on how to properly install it and link it to SwitchLinc Relay.  The following will work for the 
most common INSTEON Devices. 

1.  Set SwitchLinc Relay to 

Linking Mode

 by pressing and holding the 

Paddle 

Top

 for 10 seconds until the top LED in the LED Bar begins blinking slowly 

and the controlled light flashes.  Don’t let up too soon – 10 seconds is a 
pretty long time! 

 

 

 

 

BE CAREFUL 

Any paddle press will exit Linking Mode early.

2.  Select your INSTEON Device from the list below and follow the linking method for that Device.  You 

have about 4 minutes to perform this step before SwitchLinc Relay’s Linking Mode times out 
automatically. 

A. 

A Second SwitchLinc Relay 

– Press and hold the Second SwitchLinc Relay’s 

Paddle Top

 for 10 seconds, then release.  To confirm linking, the Second 

SwitchLinc Relay will blink the top LED in its LED Bar and flash the light that it is 
wired to. 

 

B. 

LampLinc

 V2 Dimmer

 – Press and hold the 

SET Button

 on the side of 

LampLinc V2 Dimmer for 3 seconds, then release.  To confirm linking, LampLinc 
V2 Dimmer will blink its Status LED and flash the lamp that it is controlling. 

 

C. 

ApplianceLinc

 V2 

– Press and hold the 

SET Button

 on the side of 

ApplianceLinc V2 for 3 seconds, then release.  To confirm linking, ApplianceLinc 
V2 will blink its Status LED. 

 

D. 

KeypadLinc

 V2 

– Press and hold the 

ON Button

 at the top of KeypadLinc V2 

for 10 seconds, then release.  To confirm linking, KeypadLinc V2 will blink the 
ON Button and flash the light that it is wired to. 

 

E. 

Other INSTEON Devices

 – See the INSTEON Device’s User’s Guide. 

 

 

3.  Go back to the SwitchLinc Relay that you placed in Linking Mode.  If linking was successful, the top 

LED in its LED Bar will not be blinking but will remain steadily on. 

4.  Test that your INSTEON Device is working as expected by pressing the 

Paddle Top

 and 

Paddle 

Bottom

Page 14 of 32 

 

Содержание 2476S

































Отзывы: