Smartgen APC615 Скачать руководство пользователя страница 25

Страница: 25 / 54

APC615 Pump Unit Controller User Manual

APC615 Pump Unit Controller Version 1.0 2017-10-20 Page 25 of 54

No.

Items

Parameter

Default

Description

or not, return value, and delay value can be

set.

Low Warning

(0-9000)%

Warning when value of external connected

sensor is lower than this value. Alarm enabled

or not, return value, and delay value can be

set.

Custom Curve

Users should set the corresponding curve

when select resistor curve type or current

curve type.

Rated

Outlet

Pressure

(0-9000)kPa

1000

Configure the rated working pressure of outlet.

Static Pressure

(-9000-9000)kPa 0

Configure the static pressure of outlet.

Flow Enable

(0-1)

0: Disable

；

1: Enable

Flow Unit

(0-1)

0: m³/h; 1:L/s

Rated Flow

(0-10000)m³/h

1000

Rated working flow of pump unit.

Over Flow Warning

(0-1000)%

110

While unit is running, if flow exceeds the

setting point, warning alarms will be initiated.

Alarm enabled or not, return value, and delay

value can be set.

Over

Flow

Shutdown

(0-1000)%

120

While unit is running, if flow exceeds the

setting point, shutdown alarms will be initiated.

Alarm enabled or not, return value, and delay

value can be set.

Flow Curve

Different discharge pressures correspond to

different flow values.

Flexible Sensor 1~2

Flexible

Sensor

Setting

(0-7)

0: Not used

；

1: Temperature sensor; 2:

Pressure Sensor; 3: Fuel level Sensor; 4: Flow

sensor; 5: Pipe pressure sensor; 6: Inlet

pressure sensor; 7: Water level sensor of tank.

Curve Type

It is depends on sensor type.

Open Action

(0-2)

0: Warning; 1: Shutdown; 2: No action.

Display Unit

(0-1)

℃

; 1:

℉

Note: different sense displays different unit.

High Shutdown

(0-9000)

Shutdown when external sensor value is

higher than this value. Alarm enabled or not

and delay value can be set.

Low Shutdown

(0-9000)

Shutdown when external sensor value is lower

than this value. Alarm enabled or not and delay

value can be set.

High Warning

(0-9000)

Warn when external sensor value is higher

than this value. Alarm enabled or not, return

value, and delay value can be set.

Low Warning

(0-9000)

Warn when external sensor value is lower than

Содержание APC615























































Результаты поиска

Содержание APC615

Отзывы:

Бренды по названию

Популярные бренды

Smartgen APC615, Руководство пользователя

Результаты поиска

Содержание APC615

Отзывы:

Бренды по названию

Популярные бренды