SMARTGATE 2N Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 48

SMARTGATE 2N Скачать руководство пользователя страница 9

4

2.4. Connector description

SMS sending input

Telephone line – interface FXO
RJ 11, 6/2

Telephone line – interface FXS
RJ 11, 6/2

Power supply connector
DC Jack 5,5/2,1mm

RS232C serial line
D-Sub 9 pins

2.5. Telephone Lines Connection

2.5.1. DialThru gateway – basic connection

Phone set is normally connected to extension line of PBX. Wire up SmartGate

between phone set and PBX. Link extension line of PBX to FXO interface and phone
set to FXS interface on SmartGate. Optionally you can connect analogue fax (special
model of SmartGate).

2.5.2. Gateway for extension line of PBX

Link free extension line of your PBX to FXO interface on SmartGate. FXS interface

remains unconnected.

2.5.3. Gateway for trunk line of PBX

Link free trunk line of your PBX to FXS interface on SmartGate. Program PBX to

route all GSM calls to SmartGate. Incoming calls from GSM network will be routed to
PBX.

You can connect a standard telephone, answering machine or any other FXO-interface

terminal to SmartGate. Outgoing calls from phone will be routed to GSM network, incoming
calls from GSM will ring on the phone. Optionally you can connect analogue fax (special
model of SmartGate).

SmartGate is equipped with the FSK-based CLIP and so it is advantageous to connect a

terminal that is able to display or process the CLI. You must activate the function on
SmartGate.

2.5.4. Gateway for both, trunk and extension, lines of PBX

SmartGate is very flexible thanks to his three routing tables. You can connect trunk and

extension lines of one PBX to proper connectors on SmartGate. You can program the
complex as follows: outgoing calls from PBX will be routed through trunk line to GSM
network. Incoming calls from GSM will be routed to extension line of PBX. This
configuration is suitable for PBX’s with no capability of dial-in on trunk lines.

2

4

5

1

2

3

4

5

3

1

«
...
7
8
9
10
11
...
»

Содержание 2N

















































Отзывы:

Нет отзывов