SMARTGATE 2N Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 48

background image

26

Type of transmitted dialing

Set type of dialing for automatic dial-in from GSM and for dialing during outgoing
call from FXS interface.
Setting options:

DTMF

-SmartGate transmits tone dialing

-

-for future use

Default setting: DTMF

Minimal On-Hook

[ms]

Parameter  defines  minimal  time  of  line  On-Hook  between  calls.  Set  the
parameter longer then duration of FLASH on your PBX.
Setting options:   100-25500 ms

Step:

100 ms

Default setting: 1500 ms

Maximal Off-Hook without dialing

[s]

Parameter defines maximal time of line Off-Hook before dialing to FXO interface
during  outgoing  call  from  FXS  interface.  Set  up  shorter  time  then  timeout  from
extension line Off-Hook and dialing receiver  disconnection on your PBX. In this
case  PBX  usually  changes  dial  tone  to  busy  tone.  If  defined  timeout  passes
before dialing, SmartGate shortly hangs up, after that Off-hooks again and then
dials.

Setting options: 1-255 s

Step:

1 s

Default setting: 15 s

Beep after dialing end

If SmartGate is programmed as FXO gateway, parameter enables a beep to
signal the end of dialing (beginning of outgoing call establishing).

Setting options: YES/NO
Default setting: YES

Dial tone – frequency

[Hz]

Setting of frequency/frequencies of dial tone.

Setting options: 1-3400 Hz
Setting step:

1 Hz

Default setting: 425 Hz

Dial tone - cadence

This tone is generated after Off-Hook in case SmartGate is ready to accept
dialing.

Setting options:

Continuous -SmartGate generate continuous dial tone

Morse A

-SmartGate generate dial tone with 330/330/660/660 ms

cadence

Default setting: Continuous

«
...
29
30
31
32
33
...
»

Содержание 2N

















































Отзывы:

Нет отзывов

Похожие инструкции для 2N

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: CHERUBINI Страницы: 16

pathport quattro

Бренд: pathway Страницы: 14

Бренд: WAGO Страницы: 76

Бренд: Yeastar Technology Страницы: 66

OFFICE CONNECT CABLE/DSL SECURE GATEWAY...

Бренд: 3Com Страницы: 102

Бренд: Pathport Страницы: 3

WELLGATE 26 Series

Бренд: WELLTECH Страницы: 94

Бренд: Fanvil Страницы: 71

V-NET PLNWKB000

Бренд: LG Страницы: 19

Бренд: LG Страницы: 23

V-NET PLNWKB000

Бренд: LG Страницы: 183

Бренд: LG Страницы: 11

Бренд: Plugwise Страницы: 16

Бренд: Velleman Страницы: 84

Бренд: SonicWALL Страницы: 7

Бренд: Avid Technology Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды