SMARTGATE 2N Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 48

SMARTGATE 2N Скачать руководство пользователя страница 34

29

are routed to GSM network. Their tariff is one impulse every 30 second and you can
accelerate connection establishing by dialing of a # after the dialed number.

Prefix

Dialed number prefix identifying the call type. "Other numbers" line is used for
calls with prefixes that are not included in the table.

Setting options: 0-16 characters (0-9,*,#)

Default setting: blank

Call enable

This parameter allows/bars calls with corresponding prefixes.
Setting options: YES/NO

Default setting: YES

Route to

This parameter defines FXS call routing.

Setting options:

GSM -the call is routed to GSM network only

FXO -the call is routed to FXO interface only

GSM, FXO -the call is primary routed to GSM network. In case of GSM

network error, it is routed to FXO interface

FXO, GSM -the call is primary routed to FXO interface. In case of FXO

interface error, it is routed to GSM network

Default setting: GSM

Number length

The parameter defines the expected length of dialed number. It enables to start
dialing into GSM or FXO interface immediately after the last digit is dialed. If the
telephone number to be dialed is shorter, a timeout is respected. The "0" setting
means that the function is disabled.
Setting options: 0, 3-15

Setting step:

1

Default setting: 0

End with #

This  parameter  enables  to  establish  the  call  when  a  #  is  received.  The  #
character is removed from the dialed number. If a # should be part of the dialed
number, this function cannot be used for the given prefix.
Setting options:  YES/NO

Default setting: NO

Remove

The Remove parameter is used for automatic call routing. A defined count of
digits (prefix) is removed from the number beginning.

Setting options: 0-20
Setting step:

1

Default setting: 0

«
...
32
33
34
35
36
...
»

Содержание 2N

















































Отзывы:

Нет отзывов