SMAR FP302 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 66

background image

Configuration

3.11

Figure 3.7 – Pressure Trim

Choose the unit to be used on the XD_SCALE parameter for the analog output block observing the
sensor 100% and 0% limits.

Also, on every calibration save the trim data on the CAL_POINT_LO_BACKUP and
CAL_POINT_HI_BACKUP parameters, through the BACKUP_RESTORE parameter, using the
LAST_TRIM_BACKUP option.

Via Local Adjustment

To enter the local adjustment mode, insert the magnetic screwdriver in orifice “Z” until the “MD”
readout appears in the display. Remove the magnetic tool and put it in orifice “S”. Remove and re-
insert the magnetic tool in “S” until the “Loc Adj” message appears. The message will be displayed
for 5 seconds after removing the tool. Insert the magnetic screwdriver in “Z” to access the local
adjustment and the monitoring tree.

Move to the “LOWER” parameter. To start the calibration, activate the “LOWER” parameter by
inserting a magnetic screwdriver in orifice “S”, and enter the value 3.0 psi or inferior. When removing
the magnetic tool from “S”, the output will be adjusted with a value close to the desired one. The
user must “sweep” the tree up to the FEEDBACK_CAL parameter and activate it by inserting the
magnetic screwdriver in “S” to reach the reference pressure value.

Continue writing on this parameter until reading 3.0 psi or the lower pressure value.

Move to the “UPPER” parameter. To start the calibration actuate on this parameter by inserting the
magnetic screwdriver in “S”.

It is possible to enter 30.0 psi or the wanted value wanted. When removing the magnetic
screwdriver from “S”, the output will be adjusted with a value close to the desired one. The user
must “sweep” the tree up to the FEEDBACK_CAL parameter and activate it by inserting the
magnetic screwdriver in “S” to reach the value obtained from the reference pressure.

The user should continue writing on this parameter until reading 30.0 psi.

NOTE

Exiting the Trim mode via the local adjustment is automatically done, if the magnetic screwdriver is not used for
approximately 16 seconds.

«
...
27
28
29
30
31
...
»

Содержание FP302



































































Отзывы:

Нет отзывов

Похожие инструкции для FP302

Бренд: IAdea Страницы: 16

Бренд: I-Tech Страницы: 14

Бренд: Karma Страницы: 12

Бренд: Icy Box Страницы: 2

AZZUPRO 5-20-ZSS

Бренд: ZCS Страницы: 44

Бренд: xpr Страницы: 12

Бренд: Statpower Страницы: 28

Interface Module XC Modbus

Бренд: Baer Страницы: 10

Бренд: B&K Страницы: 2

Бренд: Kaco Страницы: 52

Бренд: I-Tech Страницы: 16

Бренд: Aegis Страницы: 20

Frenic Mini FRN001C1E-2U

Бренд: Fuji Electric Страницы: 196

Бренд: Nagra Страницы: 18

Video Console II

Бренд: Converters.TV Страницы: 8

Бренд: IRiver Страницы: 32

BRAVO ST 230 VAC

Бренд: Helios Power Solutions Страницы: 39

Бренд: A-TS TECHNOLOGY Страницы: 131

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды