SMA SUNNY BOY 8000-US Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 108

background image

SMA Solar Technology AG

38

SB50US-80US-IUS094030

Installation Guide

5.1 Sequence of Connecting

5.1.1 Wiring without SMA DC-Disconnect

1. De-energize all energy sources by opening all AC and DC disconnects and/or breakers.
2. Wiring from AC breaker to the AC disconnect switch.
3. Wiring from the AC disconnect switch to the Sunny Boy, follow the procedure on page 47 et

seq..

4. Wiring from the PV wires to the DC disconnect.
5. Wiring from the DC disconnect to the Sunny Boy, follow the procedure on page 58 et seq..
6. Turn the DC switches and/or breakers ON.
7. Turn the AC switches and/or breakers ON.

To disconnect the Sunny Boy first turn OFF all AC disconnects and then all DC disconnects. The AC
system should always be disconnected before the DC system.
After the Sunny Boy is de-energized, disconnect the wiring in the reverse order from above.

WARNING!

Always connect the wires to the Sunny Boy in the following sequence:

WARNING!

Always wait a minimum of 5 minutes for stored potentials in the Sunny Boy to discharge
completely before opening the enclosure.

WARNING!

All electrical installations must be done in accordance with all local electrical codes and
the National Electrical Code (NEC), ANSI/NFPA 70.

WARNING!

Before connecting the Sunny Boy to the electrical utility grid, contact the local utility
company. This connection must be made only by qualified personnel.

«
...
36
37
38
39
40
...
»

Содержание SUNNY BOY 8000-US













































































































Отзывы:

Нет отзывов

Похожие инструкции для SUNNY BOY 8000-US

Бренд: Paradox Страницы: 2

Бренд: Z3 Technology Страницы: 86

Бренд: Oakley Страницы: 11

Бренд: Z3 Technology Страницы: 15

Бренд: Furrion net-zero Страницы: 32

DVI to VGA Conversion Box

Бренд: l-com Страницы: 7

Бренд: ZIPPER MASCHINEN Страницы: 100

TopTronic E Solar TTE-SOL

Бренд: Hoval Страницы: 95

Rossini Transport

Бренд: DCS Страницы: 31

Бренд: Plexim Страницы: 8

Бренд: Wisenet Страницы: 8

PowerClean Salt Econ

Бренд: CMP Страницы: 24

Atlona OmniStream 122

Бренд: Panduit Страницы: 12

Бренд: B&B Electronics Страницы: 2

Бренд: Avtech Страницы: 4

Бренд: NANO MACHINES Страницы: 5

Бренд: Beckhoff Страницы: 40

Бренд: HEIDENHAIN Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды