SMA SUNNY BOY 8000-US Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 108

background image

SMA Solar Technology AG

26

SB50US-80US-IUS094030

Installation Guide

4 Mounting

This section provides guidelines to help you select the best mounting location, suggestions to insure
optimum performance, cautions and warnings that you should follow to avoid injury and/or
equipment damage, and step-by-step instructions for mounting a Sunny Boy inverter.

4.1 Choosing a Mounting Location

Consider the following guidelines, cautions, and warnings when choosing a mounting location for the
Sunny Boy.

4.1.1 Selection of the Mounting Location

• The inverter should be installed in a location that is inaccessible to children.

WARNING!

The Sunny Boy weighs up to 147 lb. (67 kg). To avoid injury, be sure to use proper lifting
techniques and secure the help of someone to assist in the unpacking and installation of
the inverter.

Occasionally, the rating label on the Sunny Boy will need to be referred to. For this reason,
it is required that the inverter be mounted so that the rating label on the side of the inverter
is visible.

DANGER!
Danger to life due to fire or explosion.

There is always a certain risk with electric devices that a fire can occur, even though
greatest attention was paid to avoiding this during the development.
Do not install the inverter

• on flammable construction materials,
• in areas where highly flammable materials are stored,
• in potentially explosive areas!

CAUTION!

The Sunny Boy weighs up to 147 lb. (67 kg). Ensure that the mounting surface is strong
enough to hold the weight of the Sunny Boy. Do not mount the Sunny Boy on plasterboard
(sheet-rock) or thin wood panelling.

«
...
24
25
26
27
28
...
»

Содержание SUNNY BOY 8000-US













































































































Отзывы:

Нет отзывов

Похожие инструкции для SUNNY BOY 8000-US

BeoSound Century

Бренд: Bang & Olufsen Страницы: 29

Бренд: Vacon Страницы: 6

Бренд: Thinkpower Страницы: 30

Бренд: Helvest Страницы: 2

HD67D36-B2-868MHz

Бренд: ADF Web Страницы: 31

Бренд: LevelOne Страницы: 9

Бренд: POWER ON BOARD Страницы: 13

Бренд: Xantrex Страницы: 80

Бренд: ICT Страницы: 2

Бренд: Defort Страницы: 40

MOB31-12HFN1-QRD0GW

Бренд: Midea Страницы: 65

Бренд: Xantrex Страницы: 36

Бренд: Midian Electronics Страницы: 10

Бренд: Metrodata Страницы: 17

Бренд: Alloy Страницы: 9

Бренд: CTC Union Страницы: 2

TECHNOLOGY TIG 172

Бренд: Telwin Страницы: 29

MOVIDRIVE DFC11A

Бренд: SEW-Eurodrive Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды