SMA sunny boy 2000hf-us Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 112

background image

General Warnings

SMA America, LLC

6

SB20_25_30HFUS-eng-IUS113711

Installation Guide

General Warnings

General Warnings

All electrical installations must be done in accordance with the local and

National Electrical Code

®

ANSI/NFPA 70 or the

Canadian Electrical Code

®

CSA C22.1. This document does not and is not intended to replace any local, state,
provincial, federal or national laws, regulation or codes applicable to the installation and
use of the inverter, including without limitation applicable electrical safety codes. All
installations must conform with the laws, regulations, codes and standards applicable in
the jurisdiction of installation. SMA assumes no responsibility for the compliance or
noncompliance with such laws or codes in connection with the installation of the inverter.
The Sunny Boy contains no user-serviceable parts except for the fan on the bottom of the
enclosure. For all repair and maintenance always return the unit to an authorized SMA
Service Center.
Before installing or using the Sunny Boy, read all of the instructions, cautions, and warnings
on the Sunny Boy in this installation guide.
Before connecting the Sunny Boy to the power distribution grid, contact the local power
distribution grid company. This connection must be made only by qualified personnel.

«
...
4
5
6
7
8
...
»

Содержание sunny boy 2000hf-us

















































































































Отзывы:

Нет отзывов

Похожие инструкции для sunny boy 2000hf-us

Бренд: Data Translation Страницы: 64

Бренд: Data Translation Страницы: 84

Бренд: Data Translation Страницы: 54

Бренд: Data Translation Страницы: 54

Бренд: Sima Страницы: 2

Бренд: UNICOM Страницы: 1

Бренд: T-TeleSec Страницы: 21

CO-SinusUPS-400W

Бренд: Adler Power Страницы: 4

Бренд: KanexPro Страницы: 32

Бренд: FOLSOM Страницы: 61

Бренд: April Music Страницы: 20

Бренд: Vertiv Страницы: 40

Бренд: Katana Страницы: 162

Бренд: YOKOGAWA Страницы: 4

Бренд: Tektronix Страницы: 74

Бренд: StarTech.com Страницы: 4

Бренд: Viking Страницы: 6

Бренд: Elation Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды