SMA sunny boy 2000hf-us Скачать руководство пользователя страница 61

Страница: 61 / 112

SMA America, LLC

Wiring the Sunny Boy

Installation Guide

SB20_25_30HFUS-eng-IUS113711

Connecting the AC cable of the power distribution grid and connecting the
power supply of the fan

4. Connect the L1 wire of the power distribution grid

to the terminal (E).

5. Connect the L2 wire of the power distribution grid

to the terminal (F).

6. Connect the AC equipment ground wire from the

power distribution grid to terminals (G).

7. If there is a neutral electic conductor from the

power distribution grid: Connect the neutral
conductor from the power distribution grid to
terminal (D).

Connecting the power supply of the fan

8. Plug in the plug of the fan into socket (A). A click sound can be heard by propper connection.

Pull the fan plug slightly to ensure mechanical connection.

☑ The Sunny Boy is connected and grounded on the AC side. Fan power supply is connected.

iring

rmation see manual)

One and Two String Wiring

(for more strings and further information see manual)

e Grounding

Negative Grounding

Positive Grounding

ROUNDED

UNGROUNDED

OUNDED

GROUNDED

UNGROUNDED

OUNDED

GROUNDED

minal

Terminal

cing -

Facing -

L1 L2

D E

Содержание sunny boy 2000hf-us

















































































































Результаты поиска

Содержание sunny boy 2000hf-us

Отзывы:

Похожие инструкции для sunny boy 2000hf-us

Бренды по названию

Популярные бренды

SMA sunny boy 2000hf-us, Руководство по установке

Результаты поиска

Содержание sunny boy 2000hf-us

Отзывы:

Похожие инструкции для sunny boy 2000hf-us

Бренды по названию

Популярные бренды