SMA sunny boy 2000hf-us Скачать руководство пользователя страница 30

Страница: 30 / 112

Configuring the Sunny Boy

SMA America, LLC

SB20_25_30HFUS-eng-IUS113711

Installation Guide

Identifying the Quick Module

You can identify the Quick Module by its type label. The type label is affixed at the lid of the
Quick Module and shows name, serial number, version and type of the Quick Module.

Inner View of the Quick Module

Slot for SD card

The Quick Module contains a slot for an SD card. The slot
is on the outside of the Quick Module (A).

• To insert an SD card, flip the lower flap upwards.

In case of a firmware update an SD card is necessary. Contact the SMA Service Line for details.

Object

Description

Rotary switch for configuration of country and grid type (switch A)

Rotary switch for configuration of language and grid type (switch B)

Rotary switch for configuration of

Bluetooth

communication

Slot for SD card

Jumper socket for the configuration of the language to English

Properties of the SD Card

• A maximum of 2 GB of storage space.
• Use the SD card exclusively for this Sunny Boy. Do not save any other files on the

SD card.

Содержание sunny boy 2000hf-us

















































































































Результаты поиска

Содержание sunny boy 2000hf-us

Отзывы:

Похожие инструкции для sunny boy 2000hf-us

Бренды по названию

Популярные бренды

SMA sunny boy 2000hf-us, Руководство по установке

Результаты поиска

Содержание sunny boy 2000hf-us

Отзывы:

Похожие инструкции для sunny boy 2000hf-us

Бренды по названию

Популярные бренды