SLEIPNER MOTOR AS SRL 130/250 T Скачать руководство пользователя страница 2

Страница: 2 / 36

SRV(P)130_170_210

1.1.8 - 2017

Contents

DECLARATION OF CONFORMITY

We,

Sleipner Motor AS

P.O. Box 519

N-1612 Fredrikstad, Norway

declare that this product with accompanying

standard remote control systems complies with

the essential health and safety requirements

according to the Directive 89/336/EEC of 23

May 1989 amended by 92/31/EEC and

93/68/EEC.

Installation instructions

Measurements, thruster..............................................................3

Planning and important precautions ...........................................5

Technical specifications

..............................................................6

Thruster installation

Step by step installation .............................................................7

Fitting the electromotor ............................................................18

Electrical installation .................................................................19

150000 controller ......................................................................20

Technical & visual wiring diagrams, SRV/SRL models .............21

Technical & visual wiring diagrams, SRVP/SRLP models ........22

Check and calibrate drive shaft alignment................................23

Maintenance .............................................................................24

S-Link

S-link system overview .............................................................25

User’s manual

Control panels ..........................................................................27

General use ............................................................................28

Installation checklist................................................................. 29

Important user precautions ...................................................... 30

Troubleshooting ....................................................................... 31

Warranty statement

.............................................................. 32

Spareparts lists & drawings

................................................ 33

Содержание SRL 130/250 T





































Результаты поиска

Содержание SRL 130/250 T

Отзывы:

Бренды по названию

Популярные бренды

SLEIPNER MOTOR AS SRL 130/250 T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SRL 130/250 T

Отзывы:

Бренды по названию

Популярные бренды