Skyworks Si5391 Скачать руководство пользователя страница 73

Страница: 73 / 94

15.2 Page 1 Registers Si5391

Table 15.39. 0x0102 All Output Clock Driver Disable

Reg Address

Bit Field

Type

Setting Name

Description

0x0102

R/W

OUTALL_DISA-

BLE_LOW

0: Disables all output drivers.

1: No output drivers are disabled by this bit, but other
signals may disable the outputs.

Table 15.40. 0x0103 Clock Output 0A Configs and R0A Divider Configuration

Reg Address

Bit Field

Type

Setting Name

Description

0x0103

R/W

OUT0A_PDN

Powerdown output driver.

0: Normal Operation (default)

1: Powerdown output driver

When powered down, outputs pins will be high impe-
dance with a light pull down effect.

0x0103

R/W

OUT0A_OE

Enable/Disable individual output.

0: Disable output (default)

1: Enable output

0x0103

R/W

OUT0A_RDIV_FOR

CE2

Force R0A output divider divideby-2.

0: R0A_REG sets divide value (default)

1: Divide value forced to divide-by-2

Setting R0A_REG=0 will not set the divide value to divide-by-2 automatically. OUT0A_RDIV_FORCE2 must be set to a value of 1 to

force R0A to divide-by-2. Note that the R0A_REG value will be ignored while OUT0A_RDIV_FORCE2 = 1. See R0A_REG registers,

0x0247-0x0249, for more information.

Table 15.41. 0x0104 Clock Output 0A Format

Reg Address

Bit Field

Type

Setting Name

Description

0x0104

2:0

R/W

OUT0A_FORMAT

0: Reserved

1: normal differential

2: low power differential

3: reserved

4: LVCMOS

5–7: Reserved

0x0104

R/W

OUT0A_SYNC_EN 0 disable

1: Enable

Enable/disable synchronized (glitchless) operation.
When enabled, the power down and output enables are
synchronized to the output clock.

Si5391 Reference Manual • Si5391A/B Register Map

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

Rev. 0.5 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 11, 2022

Содержание Si5391































































































Результаты поиска

Содержание Si5391

Отзывы:

Похожие инструкции для Si5391

Бренды по названию

Популярные бренды

Skyworks Si5391, Справочное руководство

Результаты поиска

Содержание Si5391

Отзывы:

Похожие инструкции для Si5391

Бренды по названию

Популярные бренды