sitrex SR 320/8 H Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 42

background image

12

Rest the main frame (2) on stands and then insert the wear bushings

(5). Insert pin (3) into

hole (A) and fasten with the spring pin (42). Position the drawbar (1) so that pin (6) can be
inserted, and fasten pin (6) with the spring pin (7).

Mount wheels (10) on the axle pins, first placing the large guard (9) and then the small
guard (11), the washer (12) and tighten with the nut (13). Mount the parking stand (14) to
the mount on the drawbar (1), and fasten with pin (15) and clip (16). The machine can now
be placed on the ground.

«
...
10
11
12
13
14
...
»

Содержание SR 320/8 H











































Отзывы:

Нет отзывов

Похожие инструкции для SR 320/8 H

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 15

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FEBER Страницы: 2

Бренд: FASTERHOLT Страницы: 96

Бренд: Hammer Strength Страницы: 18

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренд: Land Pride Страницы: 36

Skid Steer Rakes SR2672

Бренд: Land Pride Страницы: 2

Бренд: Land Pride Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды