manualshive.com logo in svg

sitrex MK14 MY15, Сборка

Поделиться
Скачать
sitrex MK14 MY15 Скачать руководство пользователя страница 6

6

1)

 

DANGER

 

Insert bushings 4 in the openings in 
supports 2-3 (RH/LH - 40kg/88lbs).  
Lift unit 1 (weight 110kg/245lbs) with 
a suitable forklift W. Connect the 
vertical supports 2-3 to the crosspiece 
assembly 1 using pin 5, washers 6-7 
and bolt 8. 
Insert the grease nipples 9 into the 
openings in supports 2-3 and in the 
crosspiece assembly 1. 

 

In this step, you will use:  
 
Item 4:  4 bushings ø50-60x50 (ø1.97”-
2.36”x1.97”) 
Item 5:  2 pins ø50x190 (ø1.97”x7.5”) 
Item 6:  2 spacers ø23-75x12  (ø0.91”-
2.95”x0.47”) 
Item 7:  2 split washers ø23-35x4  
(ø0.91”-1.38”x0.16”) 
Item 8:  2 bolts M22x50 (0.87”x1.97”) 
Item 9:  4 grease nipples M8  (0.32”) 
 

2)

 

DANGER 

 

Work very carefully because the unit 
assembled so far is very unstable. To 
make sure that the supports 2-3 have 
been attached correctly to unit 1, 
check that the dimensions are those 
given in the drawing at the side. 
 
Note: The central holes A in the 
lower flanges of supports 2-3 must 
be on the inside.

 

Содержание MK14 MY15







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды