manualshive.com logo in svg

sitrex MK14 MY15, Сборка

Поделиться
Скачать
sitrex MK14 MY15 Скачать руководство пользователя страница 24

24

\

27) DANGER

 

Note: Spread open the machine in order to have more room to work in. 
There are two hydraulic cylinders complete with valves, one set up for the RH side indicated 
by reference 1 and one for the LH side indicated by reference 2. The assembly is correct 
when the valve is on the upper part of the cylinder and when holes A-B are facing the 
outside of the machine. Attach the cylinders 1-2 at brackets C on the drawbar and brackets D 
on arms 3-4 (RH-LH).  Fasten them to brackets C on the drawbar with pins 5, washers 6 and 
nuts 7. Fasten pins 5 to the drawbar brackets C with bolts 8 and nuts 9. Be very careful while 
attaching cylinders 1-2 to points C because they are heavy and free on one side, thus 
potentially hazardous. Now fasten them to brackets D on arms 3-4 with pins 11, washers 6 
and nuts 7. Apply grease nipples 10 to pins 5-11. If it is difficult to install cylinders 4 
because the arms 3-4 are not in perfect position, see step 22. Once the cylinders are correctly 
assembled, fully tighten the nuts and bolts from step 22.  

 

In this step, you will use:

 

Item   5:  2 pins ø30x124 (ø1.18”x4.89”)  
Item   6:  4 washers ø23-50x4 (ø0.91”-1.97”x0.16”) 
Item   7:  4 nuts  M22 (0.87”) 
Item   8:  2 bolts M12x35 (0.47”x1.38”)  
Item   9:  2 nuts  M12 (0.47”)  
Item 10:  4 grease nipples M6x45° (0.24”)   
Item 11:  2 pins ø30x124 (ø1.18”x4.89”)

Содержание MK14 MY15







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды