manualshive.com logo in svg

sitrex MK14 MY15, Сборка

Поделиться
Скачать
sitrex MK14 MY15 Скачать руководство пользователя страница 35

35

 

35) DANGER

 

The assembly is now completed. The machine is ready to be lubricated and then 
used. If for lubricating or for other reasons the machine must be moved, the 
safety arms must be rotated from the working position A-B to the transport 
position A-C. To do this you must remove the pin 2 and clip 3 from position B, 
rotate the arm until it reaches position C, and then fasten it again with pin 2 and 
clip 3. 
If it is a 14-rake wheel machine, remove the pin 2 and clip 3 that fasten the outer 
part of the arm to the inner part, then slide the inner part until it reaches the 
length indicated 1390mm/54.72” and fasten again with pin 2 and clip 3. At this 
point fasten arm 1 to point C with the pin 2 and clip 3. (If any adjustments in 
length are necessary, there are two holes available.) 
The instructions for maintenance in the following table must be carried out, 
besides this first time, according to the time schedule given, throughout the entire 
life of the machine. 
See also the sections on preparation and use of the machine. 
 

Содержание MK14 MY15







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды