Siruba LKS-1900AN Скачать руководство пользователя страница 16

Страница: 16 / 91

關於安全裝置和警告標籤

SAFETY DEVICES AND WARNING
LABELS

•

另外，在使用說明書中為了突出說明的重點，有的地方省略顯示了「護目鏡」、「手指防護器」

等安全裝置，請瞭解。

但是實際使用時，請絕對不要卸下這些安全裝置。

•

In addition, be aware that the safety devices such as the "eye protection cover" and "finger

guard" are sometimes omitted in the sketches, illustrations and figures included in the
Instruction Manual for the explanation's sake. In the practical use, never remove those safety
devices.

警告標籤(參照ⅱ頁警告標籤)

記載著操作縫紉機時的最低限
度的注意事項。

注意被夾標籤

Warning label

against pinching

Warning label(Refer to the

warning label on page ⅱ.)

Thread take-up

lever cover

這表示有把手指等夾進挑線
桿的危險。

This label warns that fingers

or other parts of human body

can be pinched in the thread

take-up lever.

The label gives the minimum

precautions to be taken when

operating the sewing machine.

This is a cover for

preventing contact

between the human

body and the thread

take-up lever.

This is a cover for preventing

contact between the human body

and the motor.

馬達護罩Motor cover

這是防止馬達和人身體接觸的護罩。

挑線桿護罩

這是防止人身體和挑
線桿接觸的護罩。

護目鏡

Eye protection cover

這是防止因斷針而傷害
眼睛的護罩。

This is a cover for

protecting eyes from

being injured by a

broken needle.

手指防護器

Finger guard

這是防止手指和機針接觸的
護罩。

This is a cover for preventing

contact between fingers

and the needle.

EU規格

EU type

觸電危險標籤

(參照ⅱ頁觸電危險標籤)

Electrical-shock danger label

(Refer to "Electrical-shock

danger label" on page ⅱ.)

記載著為了防止觸電，避免危險的安
全注意事項。

In order to protect against electrical

shock, safety precautions to be taken

to avoid danger are written on this label.

This label warns that hands can

be pinched under the sewing

machine.

注意被夾標籤

Warning label

against pinching

這表示有把手指夾進縫紉機
下面的危險。

電源開關

Power switch

這是切斷縫紉機電源裝置的電源的開關。
This is a switch for disconnecting the power

unit of the sewing machine from the power

supply.

電源開關（EU 規格）

Power switch (EU type)

這是切斷縫紉機電源裝置

的電源的開關。

同時還兼用緊急停止開關。
This switch is used for

disconnecting the power

unit of the sewing machine

from the power supply.

It is also used as the

emergency stop switch.

關於電源開關的選定

Selection of the power switch

請使用在額定電流20A以上、短路遮斷

容量120A以上的黃色背部具有紅色操

作部並符合IEC60204-1標準依據的電源

開關。
Use the IEC60204-1-compliant power

switch with rated current of 20 A or

more and short-circuit breaking capacity

of 120 A or more, which has the operating

section in red against the yellow background.

注意

CAUTION

Содержание LKS-1900AN


























































































Результаты поиска

Содержание LKS-1900AN

Отзывы:

Похожие инструкции для LKS-1900AN

Бренды по названию

Популярные бренды

Siruba LKS-1900AN, Инструкция

Результаты поиска

Содержание LKS-1900AN

Отзывы:

Похожие инструкции для LKS-1900AN

Бренды по названию

Популярные бренды