Sinclair ASC-18A Скачать руководство пользователя страница 87

Страница: 87 / 264

DC INVERTER U-MATCH AIR CONDITIONERS INSTALLATION

3.3 Specification of Connection Pipe

External Diameter

Maximum

Length of

Connection

Pipe

Maximum Difference in

Height between

Outdoor and Indoor

Unit

Additional

Charge of

Refrigerant

Model

Gas Pipe

Liquid

Pipe

(m) (m)

(g/m)

ASGE-

1/2

＂

1/4

＂

20 15

ASGE-

AI S

ASGE-

AI S

ASGE-

AI-3 S

5/8

＂

3/8

＂

30 15

ASGE-

AI-3 S

5/8

＂

3/8

＂

50 30

ASGE-

AI-3

ASGE-

AI-3

3/4

＂

1/2

＂

50 30

120

4 ELECTRIC WIRING WORK

4.1 Wiring Principle
4.1.1General

Perform wiring of the power supply in conformance with the regulations of the local electric

company.

For the control wires connecting indoor units, and between indoor and outdoor units, use of

double-core shield wires is recommended to prevent noise trouble.

Be sure to set the earth leakage breaker and the switches to the power supply section of the indoor

unit.

Supply power to each outdoor unit and provide an earth leakage breaker or hand switch for each

outdoor unit.

Store wiring system for control and refrigerant piping system in the same line.

Arrange the cables so that the electric wires do not come to contact with high-temperature part of

the refrigerant pipe; otherwise coating melts and an accident may be caused.

Do not turn on power of the indoor unit until vacuuming of the refrigerant pipe will finish.

Installation should be conducted by National Wiring Regulation.

The rated voltage and exclusive power supply must be adopted for the air conditioners.

Содержание ASC-18A









































































































































































































































































Результаты поиска

Содержание ASC-18A

Отзывы:

Бренды по названию

Популярные бренды

Sinclair ASC-18A, Руководство по обслуживанию

Результаты поиска

Содержание ASC-18A

Отзывы:

Бренды по названию

Популярные бренды