manualshive.com logo in svg

Sinclair ASC-18A, Руководство по обслуживанию

Поделиться
Скачать
Sinclair ASC-18A Скачать руководство пользователя страница 127

DC INVERTER U-MATCH AIR CONDITION                                       MAINTENANCE 

 

121

Tripping

◆

 

 

Tripping

 

If the switching

capacity can meet

the requirements?

 

Tripped once 

energized

 

Tripped when 

the compressor 

is started?

Install the electric 

switch according to the 

capacity requirements 

as specified in 

operating instructions.

Check PFC board. Cut off the

power for 1 minute or reduce

the busbar voltage to 36V or

lower. Then, remove the

connection cable on PFC board

and use multimeter to measure 

if P-N, or P-L1_2, or L1_2-N on 

PFC board is short circuited. 

Leakage current 

is too high. 

Please check for 

moisture, or 

replace the filter.

 

Short circuited?

 

The PFC module is damaged.

Replace the PFC module and check

if AC contactor is stuck. Meanwhile,

ensure that P-N is short circuited.

The possible reasons causing this

trouble include: 

①

 The screws fixing 

the module are not correctly

tightened; 

②

 The AC contactor on

AC side in parallel to the recharging

resistor is stuck, and the transient 

recharging current upon

energization is too high; 

③

 The input 

voltage is too low; or 

④

 The cable 

connection is wrong.   

Check driver board. Cut off the 

power for 1 minute or reduce 

the busbar voltage to 36V or 

lower. Then, remove the 

connection cable on driver 

board and use multimeter to 

measure if P-N, or P-U, or P-V, 

or P-W, or U-N, or V-N, or W-N 

on driver board is short 

circuited.  

Short circuited?

If the front-end 

AC contactor is

stuck?

 

If the insulation

on PFC inductor

winding is

damaged? 

The system is 

abnormal. Please check 

the compressor 

connections or winding 

for short circuiting or 

other troubles.

 

The AC contactor 

is damaged. 

Please replace 

with a same type 

of contactor.

 

Replace PFC 

inductor

 

Check if the 

cable 

connection is 

wrong

Record and 

feed back

 

Leakage current 

is too high. 

Please check for 

moisture, or 

replace the filter.

PFC ON?

No 

Yes

Yes

Yes 

Yes

Yes

Yes 

Yes 

No

No

No 

Yes

No

No

No 

The IPM module is damaged. 

Replace the driver board. The 

possible reasons causing this 

trouble include: 

①

The screws 

fixing the module are not 

correctly tightened; 

②

 The 

load is severely overloaded; or 

③

The interference causes 

short circuiting inside IPM 

module.  

No 

Содержание ASC-18A









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды