Sinclair ASC-18A Скачать руководство пользователя страница 41

Страница: 41 / 264

DC INVERTER U-MATCH AIR CONDITIONERS CONTROL

4.3 Dimension

4.4 Installation

First select an installation position. According to the size of the communication line of the wire

controller, leave a recess or a embedded wire hole to bury the communication line.

If the communication line between the wire controller (85×85×20) and the indoor unit is

surface-mounted, use 1# PVC pipe and make matching recess in the wall (refer to Figure 6); If

concealed installation is adopted, 1# PVC pipe can be used (Refer to Figure 7).

No matter if surface mounting or concealed mounting is selected, it is required to drill 2 holes (in the

same level) which distance shall be the same as the distance (60mm) of installation holes in the

bottom plate of the wire controller. Then insert a wood plug into each hole. Fix the bottom plate of

the wire controller to the wall by using the two holes. Plug the communication line onto the control

panel. Lastly install the panel of the wire controller.

Caution:

During the installation of the bottom plate of the wire controller, pay attention to the direction of the

bottom plate. The plate’s side with two notches must be at the lower position, and otherwise the panel of

the wire controller cannot be correctly installed.

Содержание ASC-18A









































































































































































































































































Результаты поиска

Содержание ASC-18A

Отзывы:

Бренды по названию

Популярные бренды

Sinclair ASC-18A, Руководство по обслуживанию

Результаты поиска

Содержание ASC-18A

Отзывы:

Бренды по названию

Популярные бренды