Sinclair ASC-18A Скачать руководство пользователя страница 103

Страница: 103 / 264

DC INVERTER U-MATCH AIR CONDITION MAINTENANCE

MAINTENANCE

1 TROUBLE TABLE

Table 1 Fault Display on Indoor Wired controller:

Trouble

Code

Trouble

Name

Origin of

Trouble Signal

Control Description

Water Pump

Malfunction

Water pump

If the water-full protection cannot be recovered after 2 hours, it is

believed that the water pump is failed, in which case all the loads

will be switched off and cannot be recovered automatically.

High Pressure

Protection of

Compressor

High-pressure

Switch

When high pressure protection is detected for 3 seconds

successively, all the loads (except the heating 4-way valve) will be

switched off, in which case all the keys and remote control signals

except ON/OFF function will be disabled and cannot be recovered

automatically. To eliminate the fault, it is needed to switch off and on

the machine or recover from power failure.

Indoor

Anti-frozen

Protetion

Indoor evaporator

sensor

If detecting that the evaporator sensor is lower than -2 after the

℃

unit has been running for a period of time under cooling or dry

mode, the unit will report this fault, in which case the compressor

and outdoor fan will be stopped. The unit will not run until this

temperature is

≥

10 and the compressor is stopped for 3 minutes.

℃

Low Pressure

Protection of

Compressor

Low-pressure

Switch

If it is detected within 30 seconds successively that the low-pressure

switch is cut off under ON or standby state (If the compressor is

started, the detection will start 3 minutes after the compressor has

run), the unit will report this fault. For the first two faults within 30

minutes, the unit can be recovered automatically. If over three times,

the unit cannot be recovered automatically.

Air Discharge

High-temperatur

e Protection of

Compressor

Exhaust

Overtemperature

Protection

After the compressor is started, if it is detected within 30 seconds

successively that the exhaust temperature is 130 or higher, E4 will

℃

be displayed, in which case all the loads (except the 4-way valve of

heating) will be stopped. The complete unit can only be recovered

until the compressor has stopped for 3 minutes and the exhaust

temperature is lower than 90 . For th

℃

is protection occurs three

times, the complete unit cannot be recovered automatically.

Overload

Proection of

Compressor

After the unit is energized, if it is detected within 3 seconds

successively that the compressor overload switch is cut off, it will be

deemed compressor overload protection. In this case, all the loads

will be stopped (except the 4-way valve of heating) and E5 will be

displayed. If the fault is eliminated, the compressor will be restarted

after 3 minutes. If three compressor overload protections are

Содержание ASC-18A









































































































































































































































































Результаты поиска

Содержание ASC-18A

Отзывы:

Бренды по названию

Популярные бренды

Sinclair ASC-18A, Руководство по обслуживанию

Результаты поиска

Содержание ASC-18A

Отзывы:

Бренды по названию

Популярные бренды