SimpliFire SF-BI30-E Скачать руководство пользователя страница 13

Страница: 13 / 26

SimpliFire • SF-BI30-E, SF-BI36-E • 2040-900 Rev. C • 2/13

B. Operating by Remote Control

• Make sure batteries are properly installed in Remote

Control.

- Battery requirements 2 x AAA batteries

(included)

•

The effective range of the remote is up to 13 ft.

• The remote control must be within the 13 ft. range and

also be pointed directly at the face of the appliance.

For best results, position the remote control within 45

degrees of the face of the appliance

C. Resetting Temperature Cutoff Switch

The heater is protected with a safety device to prevent

overheating. Should the heater overheat, an auto-

matic cutoff will turn the heater OFF. It will not turn ON

automatically without being reset. If it overheats for any

reason, it can be reset by:
1. Turn fireplace to off
2. Unplug unit and wait 5 minutes
3. Plug in and turn on.

CAUTION:

If you need to continuously reset the heater,

unplug the appliance and call your dealer.

ICON

TITLE

FUNCTION

REMOTE LCD

DISPLAY

FIREPLACE

RESPONSE

POWER

The POWER button will turn the

fireplace on. It will also put the

fireplace in a standby mode. This will

turn off all functions at once but will

hold the settings in memory except

Heater function. The unit will turn on

at the same settings by pressing the

power button again.

LCD illuminates

and displays flame

status Icon and

temperature set

point.

FLAME

By pressing the FLAME button, the unit

will cycle through four flame effects.

LCD illuminates

and displays flame

status icon.

HEATER

Press Heater button once 750W heater

turns on.

Press Heater button twice 1500W turns

on,

Press Heater button three times, turns

off heater.

LCD illuminates
and displays heater
status icon.

Two light illuminates

Three lights

illuminates

No lights illuminated

THERMOSTAT

Pressing the Temperature button

adjusts the heaters response to the

ambient temperature conditions in the

room. Temperature adjusts from 16 °C

- 28 °C (61 °F - 82 °F). Temperature

can be adjusted 1 ° at a time. Hold for

3 seconds and the LCD display from

°C to °F.

Remote displays

the temperature.

If in Stand-by

mode, temperature

displays but cannot

be adjusted.

TIMER

Pressing the Timer button sets the time

desired for the fireplace to run. The

Timer can be set from .5 hour up to 9

hours in 1 hour increments.

Remote will display

the time setting

selected. If in Stand-

by mode time will

display but cannot

be adjusted.

LIGHT

Pressing the Spotlight button will switch

the spotlight ON and OFF.

No indicator.

Fireplace will emit

one audible beep

as it transitions

between spotlight

ON and OFF states.

Содержание SF-BI30-E



























Результаты поиска

Содержание SF-BI30-E

Отзывы:

Похожие инструкции для SF-BI30-E

Бренды по названию

Популярные бренды

SimpliFire SF-BI30-E, Руководство пользователя

Результаты поиска

Содержание SF-BI30-E

Отзывы:

Похожие инструкции для SF-BI30-E

Бренды по названию

Популярные бренды