Simplex TrueAlert 4009 Series Скачать руководство пользователя

Страница: 16 / 20

Page 16

579-1019 Rev M

4009 IDNAC Repeater Installation Instructions

System Trouble LED codes

System troubles

are indicated by LEDs A to D.

Fig 16: System Trouble LED Codes

Programming

Trouble messages on the 4100ES

The table below explains the Repeater trouble messages that appear on the FACP display.

Table 9: Repeater trouble messages

Message

Definition

AC Fail

AC power is not present or is too low for proper system operation.

Low Battery

The battery voltage is below the 24 V nominal level by 10% or more.

Depleted/Missing Battery

The battery is either below 20 V or completely undetected.

Card Overcurrent

The EPS is drawing more current than it should. Check for faults on the circuit.

Charger

The battery charger is either defective or being heavily loaded by batteries. Read the charger current at the front

panel. If the charger current is approximately 2 A, the batteries are likely loading the charger. Remove the battery

connection and measure the output of the EPS. If the output is 27.6 (or close, temperature dependent), there is a

possibility the batteries are depleted, or are a bad set of batteries.
Charge the batteries or replace them if they do not take a charge.

Earth Fault Search

This is displayed during the Earth Fault Search diagnostic function. When the search is initiated, the front panel

display indicates how far along the search process has progressed for example, 10%, 25%…75%. It then shows

the results of the search. The result either identifies the offending circuit or indicates that the earth fault could

not be found. EPS circuits such as, IDNet, IDNAC, and aux power are searched. System alarm and trouble

processing is suspended during the search.

Short Circuit

This is displayed when a short is detected on the IDNAC channel. This status clears automatically when the short

circuit is removed.

Содержание TrueAlert 4009 Series





















Результаты поиска

Содержание TrueAlert 4009 Series

Отзывы:

Похожие инструкции для TrueAlert 4009 Series

Бренды по названию

Популярные бренды

Simplex TrueAlert 4009 Series, Руководство по установке

Результаты поиска

Содержание TrueAlert 4009 Series

Отзывы:

Похожие инструкции для TrueAlert 4009 Series

Бренды по названию

Популярные бренды