Simplex TrueAlert 4009 Series Скачать руководство пользователя | Manualshive

Страница: 4 / 20

background image

Page 4

579-1019 Rev M

4009 IDNAC Repeater Installation Instructions

Installing the batteries

The Repeater cabinet is built to accommodate two 12.7 AH batteries.
To safely install the batteries in the Repeater Cabinet using the battery harness, complete the following steps:

1. Place both batteries to the left side on the bottom of the cabinet.
2. Connect the positive terminal of the left battery to the positive battery input on the Repeater using the red cable.
3. Connect the negative terminal of the right battery to the negative battery input on the Repeater using the black cable.
4. Connect the two remaining battery terminals using the white jumper cable, to join the two batteries.

Negative

Jumper

Positive

Battery Input

100%

Fig 4: Installing the batteries

«
...
2
3
4
5
6
...
»

Содержание TrueAlert 4009 Series





















Отзывы:

Нет отзывов

Похожие инструкции для TrueAlert 4009 Series

Бренд: Ubisys Страницы: 2

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

DuetPro Carrycot

Бренд: Qtus Страницы: 52

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: Quickie Страницы: 108

Бренд: GARDINER TECHNOLOGY Страницы: 28

Бренд: Vent-Axia Страницы: 4

Бренд: e-survey Страницы: 12

Бренд: GEM Страницы: 31

MXI-Express Gen-3 x16

Бренд: National Instruments Страницы: 38

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 7

Бренд: Lumel Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды