Simplex APOGEE Скачать руководство пользователя | Manualshive

Страница: 11 / 63

background image

LAMPHOUSE OPTICAL ALIGNMENT

Carefully follow the lamphouse manufacturer’s instructions regarding correct optical alignment

between the lamphouse and projector. The lamphouse is generally aligned to the projector aperture, but
some consoles require positioning the projector to the optical center of the lamphouse.

Never

operate the

lamphouse with the douser open unless the projector is running.

LAMPHOUSE LIGHT SHIELD

Light shields, or nose cones, supplied by the lamphouse manufacturer, may be installed between the

projector shutter guard and the lamphouse snood. Make certain that the nose cone does not obstruct the rotation
of the shutter. Trim or otherwise modify the nose cone as required.

ELECTRICAL CONNECTIONS

All electrical connections to the Apogee terminate in the cabinet mounted on the side of the projector

adjacent to the gear compartment. Loosen the quarter-turn fastener and open the door to access the terminals.

Input voltage is user-selectable by connecting the transformer plug

to one of the two receptacles located on the top of the “Power” printed
circuit board. Connect the plug to J7 for 110 volt operation, or to J8 for
220 volt. After selecting the voltage, apply AC phase and neutral to the
two uppermost terminals on the right barrier strip. This AC input
powers the turret controller, the turret and aperture motors, and the L.E.D.
framing light. An earth ground must be connected to the ground lug at
the lower right corner of the cabinet.

The lower five terminals of the right barrier strip allow power

connections from the automation controller to the picture changeover
and the projector drive motor. The lower five terminals of the left
barrier strip provide connection points to the devices. Voltage to these
devices is generally supplied by, or switched through, the automation
controller. All NEUTRAL connections are common.

Turret inputs connect to the (4) marked terminals on the lower

part of the turret control PCB mounted to the cabinet door.

Picture Changeover

The Apogee is normally shipped with a Strong International

115 V.AC (52-60325) or 230 V.AC (52-60326) picture changeover de-
vice. If ordered separately, connect the changeover leads as follows:

Blk - OPEN

Wht - COMMON

Red - CLOSE

Grn - GROUND

NOTE: These changeover devices require an AC

pulse

to operate.

Connecting the changeover device to a

sustained

AC circuit will

destroy

the electrical coil(s). Check carefully the instructions supplied with the
automation controller and/or the (installer-supplied) switching circuit.

6

«
...
9
10
11
12
13
...
»

Содержание APOGEE
































































Отзывы:

Нет отзывов

Похожие инструкции для APOGEE

Бренд: GDC Страницы: 64

Бренд: i3 Страницы: 64

Бренд: Panamax Страницы: 1

Бренд: MAUL Страницы: 2

Бренд: ViewSonic Страницы: 57

Бренд: Black Box Страницы: 1

Бренд: BenQ Страницы: 2

Бренд: BOXLIGHT Страницы: 49

Бренд: Optoma Страницы: 2

Бренд: P3 International Страницы: 10

Бренд: HQ Power Страницы: 14

Бренд: Mitsubishi Страницы: 71

Бренд: Optoma Страницы: 2

Бренд: Hitachi Страницы: 109

7609WU - WUXGA DLP Projector

Бренд: Dell Страницы: 2

Бренд: JVC Страницы: 22

Бренд: NEC Страницы: 109

Бренд: NEC Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды