Simplex APOGEE Скачать руководство пользователя | Manualshive

Страница: 20 / 63

background image

START-UP PROCEDURES

ALL SIMPLEX PROJECTORS are carefully “run-in” at the factory before shipping. No

“run-in” period at the installation site is required. Some gear whine may be noticed initially, but should
disappear after a few hours of operation.

INITIAL OILING

One quart of Simplex Projector Oil is included in the accessory kit supplied with new equipment. USE

ONLY GENUINE SIMPLEX PROJECTOR OIL IN THE MECHANISM. Use of other lubricants may
inhibit oil pump operation and damage moving parts. Additional oil is available through authorized Strong
International Dealers; order Simplex Part No. 52-00400 for one-quart quantities, 52-00410 for a half-gallon
can, or 52-00420 for a one-gallon can.

DO NOT, at any time, operate the projector without oil.

With the projector level (0° projection angle), add oil through the filler located at the front of the gear

compartment. Look into the gear compartment while adding oil; the correct amount of oil will touch the bottom
of the horizontal drive shaft. No air bubble should be visible in the sight glass inside the film compartment.

Unless the machine is operated at a severe upward angle, no air should be visible in the sight glass. If

bubbles are seen, add oil to maintain a safe level. Always check the oil level with the motor

off.

15

Rotate the motor flywheel by hand to turn the projector mechanism. It should turn freely and smoothly.

Start the projector motor and run for at least one minute. Check for an oil splash against the gear compartment
cover glass.

Normal

Add Oil

«
...
18
19
20
21
22
...
»

Содержание APOGEE
































































Отзывы:

Нет отзывов

Похожие инструкции для APOGEE

EXECUTIVE ELECTROL

Бренд: Da-Lite Страницы: 2

TENSIONED CONTOUR ELECTROL

Бренд: Da-Lite Страницы: 8

ADVANTAGE DELUXE ELECTROL

Бренд: Da-Lite Страницы: 2

TENSIONED EXECUTIVE ELECTROL

Бренд: Da-Lite Страницы: 2

ADVANTAGE DELUXE ELECTROL

Бренд: Da-Lite Страницы: 2

Бренд: Da-Lite Страницы: 2

Carousel S-AV28

Бренд: Kodak Страницы: 8

Бренд: Goldmund Страницы: 21

Бренд: promethean Страницы: 100

Бренд: Optoma Страницы: 4

Бренд: ProLights Страницы: 36

Video Xtreme VX-2i

Бренд: Runco Страницы: 60

Бренд: Optoma Страницы: 2

Бренд: Ask Proxima Страницы: 1

Бренд: Hitachi Страницы: 65

Бренд: Hitachi Страницы: 17

Бренд: Wyrestorm Страницы: 14

Бренд: Hitachi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды