Simplex APOGEE Скачать руководство пользователя | Manualshive

Страница: 6 / 63

background image

PREFACE

THE SIMPLEX APOGEE PROJECTOR, combining rugged construction with ease of opera-

tion, provides theatre owners with a superior mechanism, engineered to the high standards set for all Strong
International products. The following design features illustrate why the Simplex Apogee Projector is able
to provide continuously excellent performance throughout its long operating life:

UNIT DESIGN

Unit method of design simplifies part replacement and maintenance. All units may be quickly

removed and replaced. Components within a particular unit are just as easily handled.

SOUND READER

The analog and digital sound reader components are mounted to the same main frame as the optical

elements, insuring a straight film path. Minimal flutter and “wow” comply with all SMPTE standards.

MAIN DRIVE

The projector main drive is connected directly to the drive motor without pulleys and belts, eliminating the

need to adjust tension and/or replace these components.

OPTICS

A conical shutter, positioned close to the picture aperture, provides very high light efficiency. Optical

design is compatible to modern xenon lamphouse systems.

LENS TURRET

The Apogee Lens Turret is available in either Automatic or Manual configurations. The standard

turret accommodates (1) each 2-25/32" (71mm) diameter Wide Screen (flat) and Anamorphic (CinemaScope)
lens without use of a MagnaCom. A three-lens turret is available for export applications. Individual focus
controls permit concise focusing of each lens independently.

FILM COMPARTMENT

The roomy film compartment permits ease of threading and cleaning. The lens turret is hinged and

swings open for added convenience.

GEAR COMPARTMENT

The gear compartment has a removable cover, rounded corners, and an enameled finish which simplifies

cleaning and service.

1

«
...
4
5
6
7
8
...
»

Содержание APOGEE
































































Отзывы:

Нет отзывов

Похожие инструкции для APOGEE

Бренд: 3M Страницы: 50

Digital Projector X75

Бренд: 3M Страницы: 4

Digital Projector X64

Бренд: 3M Страницы: 78

Digital Projector X30N

Бренд: 3M Страницы: 53

Digital Projector X30N

Бренд: 3M Страницы: 76

Digital Projector X30

Бренд: 3M Страницы: 18

Digital Projector WX66

Бренд: 3M Страницы: 16

Digital Media Systems 800 Series

Бренд: 3M Страницы: 68

Digital Media System 700P Series

Бренд: 3M Страницы: 16

Бренд: 3M Страницы: 6

Бренд: Cerio Страницы: 2

Бренд: Optoma Страницы: 4

Бренд: Monster Power Страницы: 5

Бренд: Panasonic Страницы: 127

Бренд: Panasonic Страницы: 138

Бренд: Panasonic Страницы: 212

Бренд: Panasonic Страницы: 217

Бренд: Panasonic Страницы: 265

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды