Simplex APOGEE Скачать руководство пользователя | Manualshive

Страница: 23 / 63

background image

MAINTENANCE

THE PROJECTOR MECHANISM should periodically undergo a careful and thorough

inspection. A regular schedule of adjustments and replacement of wearing parts will insure long life, provide
reliable performance, and minimize downtime.

LUBRICATION

Drain and discard the projector oil after six months of initial operation, and at least annually thereafter.

Clean the oil pump intake filter and the oil reservoir. Replace with genuine Simplex Projector Oil (Part No.
52-00400 Quart; 52-00410 Half Gallon; 52-00420 Gallon) available from Strong International Dealers.

SPROCKETS

Clean sprocket teeth daily with a typewriter brush or used toothbrush (with softened bristles). Examine

each sprocket carefully for wear, undercutting (“hooks”), and/or looseness. Replace as required. Assum-
ing the projector is used for forward-running only, hooked sprockets can be re-used by reversing the sprocket on
its shaft. Check the alignment of the intermittent sprocket to the film trap.

PAD ROLLERS

Check pad rollers for grooves, flat spots, and/or looseness. Clean rollers and shafts thoroughly to relieve

binding; replace as required. Inspect alignment of pad rollers to sprockets; centered, flanges not rubbing,
spaced (2) film thicknesses above sprocket face.

FASTENING HARDWARE

Check all fasteners (screws, nuts) for tightness. Normal operating vibration over prolonged periods may

cause fasteners to loosen. Tighten as required.

FILM GATE

Remove all foreign matter (dirt, wax) by cleaning thoroughly. Examine film runners and straps for wear;

replace if required. Check gate opening and closing slide for smooth operation; clean linear bearing to relieve
binding. The gate mount is adjustable horizontally by means of slotted mounting holes; check periodically to
insure secure gate closure.

FILM TRAP

Examine the inboard spring-loaded studio guides for free motion. Clean carefully, adjust, or replace if

grooved. Remove all foreign material from tension straps. Inspect for wear; replace if required.

To remove the trap from the main frame, release the quarter-turn fastener securing the aperture motor

cover to the shutter guard. Loosen the slotted head of the trap mounting screw. This screw is captive, and
cannot be removed. When the trap mounting screw is loose, grasp the trap plate and withdraw the trap from the
film compartment. Carefully align the electrical pins before replacing the trap.

18

«
...
21
22
23
24
25
...
»

Содержание APOGEE
































































Отзывы:

Нет отзывов

Похожие инструкции для APOGEE

SIS-PWM Silver Shield

Бренд: Energenie Страницы: 20

Бренд: Christie Страницы: 2

Бренд: Qomo Страницы: 62

Бренд: M-system Страницы: 5

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 24

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 104

Бренд: Hitachi Страницы: 116

Бренд: Hitachi Страницы: 260

Бренд: Claypaky Страницы: 24

Бренд: ION Страницы: 30

Бренд: Hitachi Страницы: 4

Бренд: Hitachi Страницы: 4

Бренд: Hitachi Страницы: 1

Бренд: Hitachi Страницы: 259

Бренд: CYP Страницы: 98

7345 - LV - LCD Projector

Бренд: Canon Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды