GB
8
Troubleshooting
available from your Silverline stockist or www.toolsparesonline.com.
Maintenance
WARNING:
ALWAYS disconnect from the power supply before cleaning or carrying out maintenance.
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Silverline service centre. This advice also applies to extension cords
used with this tool
Cleaning
WARNING:
ALWAYS wear protective equipment including eye protection and gloves when cleaning
this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device’s service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent
on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
Problem
Possible cause
Solution
Router will not operate
No supply of power
Check that power is available at source
Brushes worn or sticking
Disconnect power, open Brush Access Covers (4) & (18) and ensure brushes are not
damaged or heavily worn
Switch is faulty
Have the tool serviced by an authorised Silverline service centre
Motor components faulty or short circuited
Have the tool serviced by an authorised Silverline service centre
Router runs or cuts slowly
Blunt or damaged cutter
Resharpen or replace cutter
Variable Speed Dial (5) set low
Increase variable speed setting
Motor is overloaded
Reduce pushing force on router
Makes an unusual sound
Mechanical obstruction
Have the tool serviced by an authorised Silverline service centre
Armature has shorted sections
Have the tool serviced by an authorised Silverline service centre
Excessive vibration
Incorrectly fitted or loose router bit
Refit or tighten router bit
Heavy sparking occurs inside motor
housing
Bent or damaged router bit
Replace router bit
Brushes not moving freely
Disconnect power, remove brushes, clean or replace
Armature short circuited or open circuited
Have the tool serviced by an authorised Silverline service centre
Fine Adjustment Knob (12) “clicks” or
not adjusting
Commutator dirty
Have the tool serviced by an authorised Silverline service centre
Plunge Lock Lever (13) engaged
Release Plunge Lock Lever
Reached end of adjustment range
Reset Fine Adjustment Knob and set depth with Depth Stop Adjuster (2)
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• To replace the brushes, remove the two Brush Access Covers (4) & (18). Remove the worn
brushes and ensure the sockets are clean. Carefully replace with new brushes and then replace
the Brush Access Covers
• After fitting run the router without load for 2-3 minutes to help the brushes bed in. The process
of the brushes fully bedding in may take repeated uses. Motor sparking may continue until new
carbon brushes have bedded in
• Alternatively, have the machine serviced at an authorised service centre
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
124799_Manual2.indd 8
20/12/2017 09:43
Содержание 124799
