SILENT KNIGHT SK-2224 Скачать руководство пользователя страница 27

Страница: 27 / 62

Model SK-2224 Fire Alarm Control Panel Installation/Operation Manual

4-10

151165

Setting the SK-2866’s address

The range of valid addresses is 0-3. Each device requires a unique address. Set the dip
switches as shown in Table 4-3. See also Figure 4-9.

Mounting the SK-2866

The SK-2866 mounts into a standard 3-gang electrical box.

Follow these steps to mount the SK-2866:

1. Make sure that the SK-2866 is properly wired to the control panel. See Figure 4-9.

2. Slide the printed annunciator label into place on the SK-2866. The label fits in between the

LEDs and the clear plastic plate.

3. Place the SK-2866 into the 3-gang electrical switch box. See Figure 4-10.

Figure 4-10 Mounting the SK-2866

4. Place the cover plate over the top of the SK-2866 and align the holes. See Figure 4-10.

5. Insert the four cover plate screws into the four screw holes on the 3-gang electrical switch

box.

6. Screw the four cover plate screws into the cover plate until the cover plate fits firmly

against the SK-2866 and the electrical box. Do not over tighten.

Table 4-3: Addresses Per Dip Switch Setting

Dip Switch

Position

Equivalent

Address

Both

Open (off)

One Closed

(on)

Two

Closed (on)

Both

Closed (on)

Cover Plate
Screw

Cover Plate

Annunciator
Label In

Slide Printed

SK-2866

3-gang
Electrical Box

Содержание SK-2224































































Результаты поиска

Содержание SK-2224

Отзывы:

Бренды по названию

Популярные бренды

SILENT KNIGHT SK-2224, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SK-2224

Отзывы:

Бренды по названию

Популярные бренды