manualshive.com logo in svg

SILENT KNIGHT SK-2224, Инструкция по установке и эксплуатации

Поделиться
Скачать
SILENT KNIGHT SK-2224 Скачать руководство пользователя страница 22

Hardware Installation

151165

4-5

4.3.4

Notification Appliance Circuit Installation

Notification appliances used with the SK-2224 must be UL listed for compatibility with the 
SK-2224. Refer to the list in the Appendix at the end of this manual for a list of compatible 
devices.

For proper operation, you must use polarized notification appliances with a model 7628 4.7k 
ohm end-of-line (EOL) resistor on each circuit. Select ANSI output pattern, if desired. Output 
is configured as steady (continuous sound) for the factory default. See Section 5 for 
information on changing the pattern.

Figure 4-6  Notification Circuit Installation

4.4

Alarm and Trouble Relays

The SK-2224 has built-in relays for alarm and trouble. The alarm relay is energized during 
any alarm condition. The trouble relay is energized during any trouble or supervisory trouble 
condition. Each relay has three terminals (N.O., Common, and N.C.). Refer to Figure 3-1 for 
location of these terminals.

4.5

Auxiliary Power Circuit

The SK-2224 has a power limited auxiliary power circuit which can source up to .5A. The 
terminal is labeled “AUX PWR”. Refer to Figure 3-1 for location of this terminal.

Содержание SK-2224































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды