manualshive.com logo in svg

SILENT KNIGHT SK-2224, Инструкция по установке и эксплуатации

Поделиться
Скачать
SILENT KNIGHT SK-2224 Скачать руководство пользователя страница 15

Model SK-2224 Fire Alarm Control Panel Installation/Operation Manual

3-8

151165

3.9

Calculating Current Draw and Standby Battery

This section is for helping you determine the current draw and standby battery needs for your 
installation.

3.9.1

Worksheet Requirements

The following steps must be taken when determining SK-2224 current draw and standby 
battery requirements.

Filling in the Current Draw Worksheet, Table 3-6 (Section 3.9.3)

1. For the SK-2224, the worst case current draw is listed for the panel and is recorded in the 

table at Line A.

2. Add up the current draw for all smoke detectors and record in the table at Line B.

3. Add up all notification appliance loads and record in the table at Line C.

4. Any additional devices should be recorded at Line D. 

5. Make sure that the alarm current without the panel (Lines B-D) does not exceed 2.5 A. 

The total alarm current (including the panel, Lines A-D) should not exceed 2.75 A.

6. Complete the remaining instructions in Table 3-6 for determining battery size require-

ments.

3.9.2

Maximum Battery Standby Load

Table 3-5 shows the maximum battery standby load for the SK-2224 based on 24 and 60 hours 
of standby. The standby load calculations of line D in the Current Draw Calculation 
Worksheet (Table 3-6) must be less than the number shown in Table 3-5 for the battery size 
used and standby hours required.

Note: Batteries greater than 7 AH must be installed in a  enclosure UL listed .

Table 3-5: Maximum Battery Standby Load

Rechargeable Battery Size

Max. Load for 24 hrs. 

Standby, 5 mins. Alarm

Max. Load for 60 hrs. 

Standby, 5 mins. Alarm

7 AH

270 mA

110 mA

12 AH

425 mA

170 mA

Содержание SK-2224































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды