manualshive.com logo in svg

SILENT KNIGHT SK-2224, Инструкция по установке и эксплуатации

Поделиться
Скачать
SILENT KNIGHT SK-2224 Скачать руководство пользователя страница 24

Hardware Installation

151165

4-7

4.7

Optional Accessories Installation

This section describes how to install the optional accessories compatible with the SK-2224 
control panel.

4.7.1

Installing the Serial Driver Board (Model SK-2884)

The SK-2884 is required if the installation uses any SK-2224 expansion devices such as 
Model SK-2880 (I/O Module), Model SK-2866 (LED Annunciator), or Model SK-2104 
(DACT). The SK-2884 interfaces all the expansion devices to the SK-2224 control panel.

Note: The SK-2104 Dialer board is not available for control panels that have the releasing (cross alarming) 

feature.

Follow these steps to install the SK-2884 Serial Driver Board:

1. Unplug the AC power connector from the SK-2224 control panel. See Figure 4-1.

2. Unplug the battery connector from the SK-2224 control panel. See Figure 4-2.

3. Plug the SK-2884 Serial board onto the SK-2224 control panel by aligning the 4-pin con-

nector and the stand-offs with their respective receptors. See Figure 4-8.

Figure 4-8  Model SK-2884 Connector and Stand-off alignment

4. Reconnect the AC power connector to the control panel. See Figure 4-1.

5. Reconnect the battery connector to the control panel. See Figure 4-2.

Содержание SK-2224































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды