background image

3

Signet 2537 Flowmeter

3. Installation

3.3  Plastic sensor installation tips

• 

Inspect the sensor O-rings for nicks and other damage that 
may compromise the seal. 

• 

Lightly lubricate the sensor O-rings with a suitable lubricant 
before each installation.  Do not use petroleum based 
lubricants. 

• 

Using an alternating/twisting motion, lower 
the sensor into the 

fi

 tting, making sure the 

conduit ports on the yellow housing are 
pointing in the direction of 

fl

 ow.

• 

Engage one thread of the sensor cap then 
turn the sensor until the alignment tab is 
seated in the 

fi

 tting notch.

• 

sensor

cap

tab

notch

Wiring

Electrical connections to this product should be made only by 
quali

fi

 ed personnel.

To access the wiring terminals:
• 

Turn yellow cap ¼ turn counterclockwise to remove.

• 

Remove the two retaining screws and remove the black 
cover.

• 

Route all cables through the conduit ports before 
connecting them to the terminals.

• 

Wiring terminals are rated for 16-22 AWG conductors. 

• 

The cable must be 7 to 10 mm in diameter (0.275 to 0.394 
in.) to seal properly in the liquid tight connector.

• 

The conduit ports have ½ inch NPT threads. After 
routing the cables, seal the port with a liquid tight conduit 
connector (3-9000.392-1) or with conduit. 

• 

For conduit installations:

•  Thread conduit with ½ in. NPT threads directly into the 

conduit port.

•  For conduit with ISO threads, use the black thread 

adapter included with the connector kit.

•  To comply with NEC requirements, do not use any metal 

conduit in the installation.

2537 Paddlewheel Flowmeter
for ½ in. to 4 in. pipe

130 mm
5.12 in.

97 mm
3.82 in.

2537 Paddlewheel Flowmeter
for 5 to 8 in. pipe

171 mm
6.73 in.

97 mm
3.82 in.

Dimensions

S1

S1

S2

S2

3-8900.621C

I/O Module 3-8900.401-X

1

2

3

4

5

6

7

8

9

10

11

12

13

14

+5VDC (Black)

Freq. Input (Red)

GND (Shield)

+5VDC (Black)

Freq. Input 2 (Red)

S  L (Red)

GND (White/Shield)

+5VDC (Black)

S  L (Red)

GND (White/Shield)

3

3

Analog Output 1

Analog Output 2

(if applicable)

(if applicable)

Frequency

Input

1

Frequency

Input 2

OR

S3L

Input

2

S3L

Input

1

+

-

+

-

Blk

Red Shld

-

+

Wiring:  Digital (S

3

L) Output

The Digital (S

3

L) output is compatible with the 3-8900 Multi-Parameter Controller.

-

+

S1

S2

Blk

Red Shld

-

+

-

+

-

+

-

+

-

+

T

P

t

WIRING DIAGRAM

BLK

RED

SHLD

Sensor

PW/OUT

+

Power Rating:

5 - 6.5VDC           0.03 AMP

3-2505.613A

T

P

t

T

P

t

T

P

t

S1

S2

Blk

Red Shld

-

+

S1

S2

Blk

Red Shld

-

+

WIRING DIAGRAM

BLK

RED

SHLD

Sensor

PW/OUT

+

Power Rating:

24VDC            0.03 AMP

3-2505.61

1A

N/O

COM

N/C

Dry-Contact

Relay

Relay Rating:

5A @ 250VAC

5A @ 30VDC

Using the liquid-tight
connector

Using conduit

HAND-TIGHTEN THE THREADED NUT ONTO THE 
INSTALLATION FITTING.  DO NOT USE TOOLS! DO 
NOT USE THREAD SEALANT OR LUBRICANTS ON 
THE FITTING THREADS OR THE SENSOR CAP.

Содержание 159 001 291













Отзывы: