Laboratory Centrifuge Sigma 2-16P
3 Safety
24 / 76
Version 04/2007, Rev. 2.23 of 28/04/2022
• sb
Translation from the original operating manual, part no. 0700602
Pos : 58 / 100 Sigma/ 100 BA Zentrif ugen Sigma (Standar dmodule)/ 030 Sic her heit /030-0070 Sic herheits einric ht ung en----------------------------------------- @ 27\mod_1405319034809_68. doc x @ 192157 @ 2 @ 1
→
3.7
Safety devices
Pos : 59 / 100 Sigma/ 100 BA Zentrif ugen Sigma (Standar dmodule)/ 030 Sic her heit /030-0070-0010 D eck elverri egelung @ 27\m od_1405319036321_68.docx @ 192171 @ 3 @ 1
→
3.7.1
Lid lock device
The centrifuge can only be started when the lid is properly closed. The
electrical lock must be locked. The lid can only be opened when the rotor
has stopped. If the lid is opened by way of the emergency release system
during operation, the centrifuge will immediately switch off and decelerate
brakeless. If the lid is open, the drive is completely separated from the
mains power supply, i.e. the centrifuge cannot be started (see chapter 7.1.1
- "Emergency lid release").
Pos : 60 / 010 U nivers almodule/ Leerz eile @ 0\m od_1202116244500_0. doc x @ 114 @ @ 1
Pos : 61 / 100 Sigma/ 100 BA Zentrif ugen Sigma (Standar dmodule)/ 030 Sic her heit /030-0070-0020 Stillst ands überw achung @ 27\mod_1405319037803_68. docx @ 192185 @ 3 @ 1
→
3.7.2
Standstill monitoring system
Opening of the centrifuge lid is only possible if the rotor is at a standstill.
This standstill is checked by the microprocessor.
Pos : 62 / 010 U nivers almodule/ Leerz eile @ 0\m od_1202116244500_0. doc x @ 114 @ @ 1
Pos : 63 / 100 Sigma/ 100 BA Zentrif ugen Sigma (Standar dmodule)/ 030 Sic her heit /030-0070-0032 Syst emk ontroll e Spincontr ol Basic+ Eas y+Univ ersal @ 27\mod_1405319041777_68. docx @ 192227 @ 3 @ 1
3.7.3
System check
An internal system check monitors the data transfer and sensor signals with
regard to plausibility. The system continuously performs a self-check and
identifies malfunctions. Malfunctions are indicated by error messages with a
number in the speed/rcf display (see chapter 7.2 - "Table of error codes").
Pos : 64 / 010 U nivers almodule/ Leerz eile @ 0\m od_1202116244500_0. doc x @ 114 @ @ 1
Pos : 65 / 100 Sigma/ 100 BA Zentrif ugen Sigma (Standar dmodule)/ 030 Sic her heit /030-0070-0040 Sc hutzleit erpr üf ung mit Pot ential ausgleichssc hraube @ 27\mod_1405319043129_68.docx @ 192241 @ 3 @ 1
→
3.7.4
Earth conductor check
For the earth conductor check, there is an equipotential bonding screw on
the rear panel of the centrifuge (see chapter 2.1.1 - "Functional and
operating elements"). An earth conductor check can be carried out by
authorized and specialized personnel using a suitable measuring
instrument. Please contact the service department (see chapter 7.3 -
"Service contact").
Pos : 66 / 010 U nivers almodule/ Leerz eile @ 0\m od_1202116244500_0. doc x @ 114 @ @ 1
Pos : 67 / 100 Sigma/ 100 BA Zentrif ugen Sigma (Standar dmodule)/ 030 Sic her heit /030-0070-0051 U nw uchtüberwac hung Spi ncontr ol L+Easy+U nivers al @ 27\m od_1405319047031_68.docx @ 192283 @ 3 @ 1
→
3.7.5
Imbalance monitoring system
The indication "Imbalance" in the rotor field and, in some cases, also a
sound signal indicate that the centrifuge is in the impermissible imbalance
range.The drive will be switched off in the acceleration phase or during the
run.
Pos : 68 / 010 U nivers almodule/ Seitenw ec hsel @ 0\m od_1202116244312_0. docx @ 105 @ @ 1
