Siemens ST950 Скачать руководство пользователя страница 65

Страница: 65 / 178

ST950 Plus+ User Manual

Page 65 of 176

667/HE/53000/000

Issue 2

Unrestricted

3.16.14

CIC/CTB Status LEDs

The status LEDs provide an engineer with some information on the correct operation of the CIC.

The CIC has six LEDs (three per CPU) which are used to indicate various conditions as follows;

LED

Illumination Function

LP1x

–

(Green)

System/Software
Run

Slow Flash

Software is operating normally (typically flashing once per
second)

Off

CIC has detected a persistent fatal error and has entered a non-
operational state to prevent continual restarts. This state can only
be left by power cycling the CIC (with Comms LED off and Fault
LED illuminated).

LP2x

–

(Red)

Fault

Off

Normal Operation

Fault Detected

LP3A

–

(Green)

Communications

Normal Operation.

Off

No relevant messages received in the last second (implies loss of
communications), or low power mode.

LP3B

–

(Green)

Communications

Normal Operation.

Off

No relevant messages received in the last second (implies loss of
communications), or low power mode.

Table 11 : CIC LED Status Indicators

Indication of Fault

Conditions other than those identified above should not occur and so can be treated as faults.

Содержание ST950



















































































































































































Результаты поиска

Содержание ST950

Отзывы:

Бренды по названию

Популярные бренды

Siemens ST950, Руководство пользователя

Результаты поиска

Содержание ST950

Отзывы:

Бренды по названию

Популярные бренды