manualshive.com logo in svg

Siemens ST950, Руководство пользователя

Поделиться
Скачать
Siemens ST950 Скачать руководство пользователя страница 25

 

ST950 Plus+ User Manual 

 

  

 

ST950 Plus+ User Manual 

Page 25 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

 

Plus+ STS drawing

 

On completion of a Traffic Junction Design (STS Drawing) the Plus+ Design Layout Tool will be 

used  to  generate  the  Plus+  Design  Layout  Configuration.  This  configuration  can  either  be 

imported directly to a controller or passed to the Plus+ Installation App. 

The STS drawing contains all the pertinent information for on- street cable connections and should be 
referred to accordingly. 

 

 

When a Traffic Junction is being built up, within a depot or out on street, the Plus

+

 Installation App 

provides an easy method (scanning) to populate the Plus+ Design Layout Configuration with the 
serial numbers of the relevant Nodes.  

It is this mapping between Nodes, having a defined function, and the serial number of the physical 
Node  that  is  going  to  implement  the  function  that  ensures  the  configuration  from  IC4  is 
implemented in the controller when on street. 

Further information on using the Plus

+

 Design Layout Tool can be found in the Plus

+

 Design Layout 

Tool Quick Start Guide 667/HQ/53000/200.  

Further information on using the Plus

+

 Installation App can be found in the Plus

+

 Installation App 

Quick Start Guide 667/HQ/53000/300.  

 

 

Plus

+

 : Key Considerations 

2.4.1

 

Reserve State 

The reserve state, in Plus+, is slightly different from the standard ST950 controller. 

•

 

Ped Phases are no longer inhibited 

•

 

The user can now add and should include Ped stages in the Fixed Time sequence. 

•

 

Audible devices all switched off 

•

 

Tactile devices continue to operate, but ignore tactile disable from S/C using SCTACDIS 

•

 

I/O  still  unavailable  so  Wait  /  Demand  Indicators  illuminate  and  on-crossing  clearance 
periods run to max. 
 

Note that the IC4 defaults for Reserve State have not been changed for Plus+ Controllers, so: 

•

 

junctions with RLM configured to extinguish streams (typically part-time junctions) are still 
extinguished by default 

•

 

stand-alone pedestrian crossings are held at vehicle green / pedestrian red. 

2.4.2

 

Red Lamp Monitoring 

When the IC4 configuration is being compiled the user may see a warning message: “

For Plus+ 

Controllers it is recommended that RLM RLF1/RLF2 actions are NOT latched until manually reset 
(RFL=1) unless there are valid traffic engineering reasons.

”

 

Содержание ST950



















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды