Siemens ST950 Скачать руководство пользователя страница 23

Страница: 23 / 178

ST950 Plus+ User Manual

Page 23 of 176

667/HE/53000/000

Issue 2

Unrestricted

Figure 9 : Smartloop Layout Example 4 : MOVA

Configuration

One of the fundamental changes, that has been brought about by Plus

, is that there no longer is

a 1:1 link between outputs from a controller lamp switch card and the individual aspects. This link
is now achieved out on-street, between the Node and the aspect, push button or pedestrian
display unit.

In order to

‘link’ the functional design (IC4) and the on

-street equipment a new layer of

configuration is required. It is known as the Plus

Design Layout Configuration.

For Plus

, the IC4 configuration is fundamentally unchanged, where the traffic junction

configuration (operation) is defined, terms of streams, phases, lamp monitoring and detector
inputs.

The Plus

Design Layout Configuration now provides the link between the IC4 configuration and

the junction layout as designed

–

as opposed to wiring in a Lamp Switch Card.

Siemens Mobility has developed the Plus

Design Layout Tool, which works hand in hand with

KeySignals (KeySoft product). KeySignals provides a toolset for Traffic Engineers to design their
junctions within the AutoCAD product suit.

Plus+ Street Cable

from RAG Node

Torpedo

joint

Loop Feeder

45m

100m

S
L

SmartLoop

Plus+ Loops

S
L

Torpedo

joint

Torpedo

joint

Torpedo

joint

SmartLoop

Plus+ Loops

Plus+ Street Cable from

Upstream Smartloop

Содержание ST950



















































































































































































Результаты поиска

Содержание ST950

Отзывы:

Бренды по названию

Популярные бренды

Siemens ST950, Руководство пользователя

Результаты поиска

Содержание ST950

Отзывы:

Бренды по названию

Популярные бренды