manualshive.com logo in svg

Siemens ST950, Руководство пользователя

Поделиться
Скачать
Siemens ST950 Скачать руководство пользователя страница 140

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 140 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

9.3.9

 

Intermittent Faults/Problem Sites 

If  a  site  has  an  intermittent  fault  or  a  fault  which  keeps  repeating,  then  first  the  appropriate 
procedure for the fault should be followed as most paths have more than one suggested area to 
check for the fault. 

If the fault is still intermittent, do the following: 

•

 

Gently - try and move/flex each card whilst in situ to check for any intermittent connections. 

•

 

If any intermittent connections are found, replace appropriate card. 

•

 

Gently move cables and wiring looms to check for any intermittent connections. 

•

 

Switch controller ‘off’ and withdraw all cards. Check security of any ICs mounted in socket

s 

on the CPU Card.  

•

 

Re-fit cards and re-check operation of controller. 

9.3.10

 

Faults with Handset  

If the handset does not operate correctly when plugged into the handset port on Main CPU Card, 
do the following: 

•

 

Check that the H5V supply fuse (F1) on the CPU Card is intact. 

•

 

Check that there is a +5V supply on pins 9 and 10 of the handset socket (0V is on pins 1, 7, 

18 and 19). With the handset plugged in check the ripple voltage on 5V supply. 

•

 

(This supply powers those handsets that do not have their own supplies.) 

•

 

To fully investigate, this supply may require the use of an oscilloscope. 

•

 

Switch off controller and withdraw Main CPU Card. Check security of ICs mounted in sockets 

of the above card. If no loose ICs are found, replace Main CPU Card. 

•

 

Replace Main CPU Card and re-check to see if handset now operates correctly. 

 

 

Содержание ST950



















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды