Siemens SITRANS L Series Скачать руководство пользователя страница 86

Страница: 86 / 106

Diagnostics and troubleshooting

12.4 Status messages according to NE 107

more detailed error messages available under the menu item "

Diagnostics

via

the

respective adjustment module.

Status messages

The status messages are divided into the following categories:
• Failure
• Function check
• Out of specification
• Maintenance required
and explained by pictographs:

Failure - red

Out of specification - yellow

Function check - orange

Maintenance required - blue

Figure 12.1

Pictographs of the status messages

Failure:

Due to a malfunction in the transmitter, a fault message is output.

This status message is always active. It cannot be deactivated by the user.

Function check:

The transmitter is being worked on, the measured value is

temporarily invalid (for example during simulation).
This status message is inactive by default.

Out of specification:

The measured value is unreliable because an transmitter

specification was exceeded (e.g. electronics temperature).
This status message is inactive by default.

Maintenance required:

Due to external influences, the transmitter function is

limited. The measurement is affected, but the measured value is still valid. Plan in

maintenance for the transmitter because a failure is expected in the near future (e.g.

due to buildup).
This status message is inactive by default.

Failure

Code
Text message

Cause

Rectification

DevSpec
State in CMD 48

F013

No measured value in the

switch-on phase or during

operation

Check or correct installation

and/or parameter settings

Byte 5, Bit 0 of

Byte 0 … 5

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 86 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: